поискавой системы для электроныых деталей |
|
ADC0820CNEN датащи(PDF) 8 Page - NXP Semiconductors |
|
ADC0820CNEN датащи(HTML) 8 Page - NXP Semiconductors |
8 / 14 page Philips Semiconductors Linear Products Product specification ADC0820 8-Bit, high-speed, µP-compatible A/D converter with track/hold function August 31, 1994 575 FUNCTIONAL DESCRIPTION General Operation The ADC0820 uses two 4-bit flash A/D converters to make an 8-bit measurement (Block Diagram). Each flash ADC is made up of 15 comparators which compare the unknown input to a reference ladder to get a 4-bit result. To take a full 8-bit reading, one flash conversion is done to provide the 4 most significant data bits (via the MS flash ADC). Driven by the 4 MSBs, an internal DAC recreates an analog approximation of the input voltage. This analog signal is then subtracted from the input, and the difference voltage is converted by a second 4-bit flash ADC (the LS ADC), providing the 4 least significant bits of the output data word. The internal DAC is actually a subsection of the MS flash converter. This is accomplished by using the same resistor ladder for the A/D as well as for generating the DAC signal. The DAC output is actually the tap on the resistor ladder which most closely approximates the analog input. In addition, the “sampled data” comparators used in the ADC0820 provide the ability to compare the magnitudes of several analog signals simultaneously, without using input summing amplifiers. This is especially useful in the LS flash ADC, where the signal to be converted is an analog difference. The Sampled-Data Comparator Each comparator in the ADC0820 consists of a CMOS inverter with a capacitively-coupled input (Figure 4). Analog switches connect the two comparator inputs to the input capacitor (C) and also connect the inverter’s input and output. This device in effect now has one differential input pair. A comparison requires two cycles, one for zeroing the comparator, and another for making the comparison. In the first cycle, one input switch and the inverter’s feedback switch (Figure 4a) are closed. In this interval, C is charged to the connected input (V1) less the inverter’s bias voltage (VS, approximately 1.6V). In the second cycle (Figure 4b), these two switches are opened and the other (V2) input’s switch is closed. The input capacitor now subtracts its stored voltage from the second input and the difference is amplified by the inverter’s open loop gain. The inverter’s input (VS’) becomes V S + V S ) (V2 – V1) C C ) C S and the output will go High or Low depending on the sign of V’S’-VS. The actual circuitry used in the ADC0820 is a simple but important expansion of the basic comparator described above. By adding a second capacitor and another set of switches to the input (Figure 5), the scheme can be expanded to make dual differential comparisons. In this circuit, the feedback switch and one input switch on each capacitor (Z switches) are closed in the zeroing cycle. A comparison is then made by connecting the second input on each capacitor (S switches) and opening all of the other switches. The change in voltage at the inverter’s input, as a result of the change in charge on each input capacitor, will now depend on both input signal differences. Architecture In the ADC0820, 15 comparators are used in the MS and LS 4-bit flash A/D converters. The MS (most significant) flash ADC also has one additional comparator to detect input over-range. These two sets of comparators operate alternately, with one group in its zeroing cycle while the other is comparing. • VS’ – VS = (V2 – V1) • VO’ = [CV2 – CV1] • VO’ IS DEPENDENT ON V2–V1 C C + CS –A C + CS V1 V2 C VS CS VO a. Zeroing Phase b. Compare Phase V1 V2 C VS CS VO • VO = VS • V ON C = V1 – VB • CS = SATRAY INPUT NODE CAPACITOR • VS = INVERTER INPUT BIAS VOLTAGE A A Figure 4. Sampled Data Comparator VO = [C1 (V2 – V1) + C2 (V4–V3)] = [ ∆QC1 + ∆QC2] –A C1 + C2 + CS VS CS VO A C1 C2 S Z Z S Z R LADDER (V1) VIN (V2) ANALOG GND (V3) 1/2 LSB (V4) –A C1 + C2 + CS Figure 5. ADC0820 Comparator (From MS Flash ADC) |
Аналогичный номер детали - ADC0820CNEN |
|
Аналогичное описание - ADC0820CNEN |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |