поискавой системы для электроныых деталей
  Russian  ▼
ALLDATASHEETRU.COM

X  

TDA8020 датащи(PDF) 9 Page - NXP Semiconductors

номер детали TDA8020
подробное описание детали  Dual smart card interface
Download  24 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
производитель  PHILIPS [NXP Semiconductors]
домашняя страница  http://www.nxp.com
Logo PHILIPS - NXP Semiconductors

TDA8020 датащи(HTML) 9 Page - NXP Semiconductors

Back Button TDA8020 Datasheet HTML 5Page - NXP Semiconductors TDA8020 Datasheet HTML 6Page - NXP Semiconductors TDA8020 Datasheet HTML 7Page - NXP Semiconductors TDA8020 Datasheet HTML 8Page - NXP Semiconductors TDA8020 Datasheet HTML 9Page - NXP Semiconductors TDA8020 Datasheet HTML 10Page - NXP Semiconductors TDA8020 Datasheet HTML 11Page - NXP Semiconductors TDA8020 Datasheet HTML 12Page - NXP Semiconductors TDA8020 Datasheet HTML 13Page - NXP Semiconductors Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 24 page
background image
2001 Aug 15
9
Philips Semiconductors
Product specification
Dual smart card interface
TDA8020HL
READING STATUS
START, ADDRESS, READ, STATUS byte, STOP.
Table 4
STATUS bits (all bits cleared after power-on, except SUPL and PRES)
When one of the bits PRESL, MUTE, EARLY and PROT is set, then pin IRQ goes LOW until the status byte has been
read. After power-on, bit SUPL is set until the status byte has been read, and pin IRQ is LOW until the supervisor
becomes inactive.
NAME
BIT
DESCRIPTION
PRES
0
set when the card is present; reset when the card is not present
PRESL
1
set when the card has been inserted or extracted; reset when the status has been read
I/O
2
set when I/O is HIGH and reset if I/O is LOW
SUPL
3
set when the supervisor has signalled a fault; reset when the status has been read
PROT
4
set when an overload or an overheating has occurred during a session; reset when the
status has been read
MUTE
5
set during ATR when the selected card has not answered during the ISO 7816 time slots
EARLY
6
set during ATR when the selected card has answered too early
ACTIVE
7
set if the card is active; reset if the card is inactive
DC/DC converter
VCC1 is the supply voltage for card 1 contacts, VCC2 for
card 2 contacts. Card 1 and card 2 may be independently
powered-down, powered at 5 V or powered at 3 V. A
capacitor type step-up converter is used for generating
these voltages. This step-up converter acts either as a
doubler, tripler or follower.
If VCC is the maximum value of VCC1 and VCC2, then there
are 4 possible situations:
• VDD = 3 V and VCC = 3 V: in this case, the DC/DC
converter acts as a doubler with a regulation of
approximately 4.0 V
• VDD = 3 V and VCC = 5 V: in this case, the DC/DC
converter acts as a tripler with a regulation of
approximately 5.5 V
• VDD = 5 V and VCC = 3 V: in this case, the DC/DC
converter acts as a follower: VDD is applied on VUP
• VDD = 5 V and VCC = 5 V: in this case, the DC/DC
converter acts as a doubler with a regulation of
approximately 5.5 V.
The switch between the modes is automatically executed
when VDD is approximately 3.4 V.
Each card may independently draw a current up to 65 mA,
also during activation, with a supply voltage from 2.5 V up
to 6.5 V provided the sum of ICC1 and ICC2 does not
exceed 80 mA.
If VDD > 3 V, for 5 V cards, then both cards can draw up to
55 mA at the same time.
If VDD > 3.3 V, for 3 V cards, then both cards can draw up
to 50 mA at the same time.
The DC/DC converter is powered with specific pins (VDDA
and AGND) to enable separate decoupling.
The output voltage, VUP, is internally fed to the VCC
generators. VCC1,VCC2 and CGND1, CGND2 are used as
a reference for all other cards contacts.
Sequencers and clock counter
Two sequencers are used to ensure activation and
deactivation sequences according to ISO 7816 and
EMV norms, even in the event of an emergency (card
removal during transaction, supply drop-out and hardware
problem).
The sequencers are clocked by the internal oscillator.
The activation of a card is initiated by setting the card
select bit and the start bit within the control register. This is
only possible if the card is present and if the voltage
supervisor is not active.
During activation the DC/DC converter is initiated (except
if another card is already powered up or if VDD = 5 V and
VCC = 3 V). VCC then goes high to the selected voltage
(3 or 5 V), the I/O lines are then enabled and the clock is
started with RST LOW.


Аналогичный номер детали - TDA8020

производительномер деталидатащиподробное описание детали
logo
NXP Semiconductors
TDA8020HL PHILIPS-TDA8020HL Datasheet
143Kb / 28P
   Dual IC card interface
2003 Nov 06
TDA8020HLC1 PHILIPS-TDA8020HLC1 Datasheet
143Kb / 28P
   Dual IC card interface
2003 Nov 06
TDA8020HLC2 PHILIPS-TDA8020HLC2 Datasheet
143Kb / 28P
   Dual IC card interface
2003 Nov 06
More results

Аналогичное описание - TDA8020

производительномер деталидатащиподробное описание детали
logo
Dallas Semiconductor
DS8007 DALLAS-DS8007 Datasheet
350Kb / 41P
   Multiprotocol Dual Smart Card Interface
logo
Maxim Integrated Produc...
DS8007A MAXIM-DS8007A Datasheet
410Kb / 41P
   Multiprotocol Dual Smart Card Interface
Rev 0; 4/08
logo
ON Semiconductor
NCN6804 ONSEMI-NCN6804 Datasheet
341Kb / 25P
   Dual Smart Card Interface IC
December, 2008 ??Rev. 1
logo
STMicroelectronics
L6605 STMICROELECTRONICS-L6605 Datasheet
202Kb / 10P
   SMART CARD INTERFACE
logo
Linear Technology
LTC1755 LINER-LTC1755_1 Datasheet
204Kb / 16P
   Smart Card Interface
logo
Teridian Semiconductor ...
73S8010C TERIDIAN-73S8010C Datasheet
346Kb / 27P
   Smart Card Interface
73S8014RN TERIDIAN-73S8014RN Datasheet
395Kb / 28P
   Smart Card Interface
logo
Maxim Integrated Produc...
DS8113 MAXIM-DS8113 Datasheet
160Kb / 17P
   Smart Card Interface
Rev 1; 2/08
DS8023 MAXIM-DS8023 Datasheet
251Kb / 17P
   Smart Card Interface
Rev 1; 4/13
73S8014BN MAXIM-73S8014BN Datasheet
542Kb / 29P
   Smart Card Interface
Rev 2; 12/11
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24


датащи скачать

Go To PDF Page


ссылки URL




Конфиденциальность
ALLDATASHEETRU.COM
Вашему бизинису помогли Аллдатащит?  [ DONATE ] 

Что такое Аллдатащит   |   реклама   |   контакт   |   Конфиденциальность   |   обмен ссыками   |   поиск по производителю
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com