поискавой системы для электроныых деталей |
|
CS4365-CQZ датащи(PDF) 7 Page - Cirrus Logic |
|
CS4365-CQZ датащи(HTML) 7 Page - Cirrus Logic |
7 / 52 page DS670F1 7 CS4365 VQ 21 Quiescent Voltage (Output) - Filter connection for internal quiescent voltage. VQ must be capacitively coupled to analog ground, as shown in the Typical Connection Diagram. The nom- inal voltage level is specified in the Analog Characteristics and Specifications section. VQ pre- sents an appreciable source impedance and any current drawn from this pin will alter device performance. However, VQ can be used to bias the analog circuitry assuming there is no AC signal component and the DC current is less then the maximum specified in the Analog Char- acteristics and Specifications section. FILT+ 20 Positive Voltage Reference (Output) - Positive reference voltage for the internal sampling cir- cuits. Requires the capacitive decoupling to analog ground as shown in the Typical Connection Diagram. AOUTA1 +,- AOUTB1 +,- AOUTA2 +,- AOUTB2 +,- AOUTA3 +,- AOUTB3 +,- 39,40 37,38 35,36 33,34 29,30 27,28 Differential Analog Output (Output) - The full-scale differential analog output level is specified in the Analog Characteristics specification table. MUTEC1 MUTEC2 MUTEC3 MUTEC4 MUTEC5 MUTEC6 41 26 25 24 23 22 Mute Control (Output) - The Mute Control pins go high during power-up initialization, reset, muting, power-down or if the master clock to left/right clock frequency ratio is incorrect. These pins are intended to be used as a control for external mute circuits on the line outputs to pre- vent the clicks and pops that can occur in any single supply system. Use of Mute Control is not mandatory but recommended for designs requiring the absolute minimum in extraneous clicks and pops. Hardware Mode Definitions M0 M1 M2 M3 M4 17 16 15 12 10 Mode Selection (Input) - Determines the operational mode of the device as detailed in Table 6 and Table 7. Software Mode Definitions SCL/CCLK 15 Serial Control Port Clock (Input) - Serial clock for the serial control port. Requires an external pull-up resistor to the logic interface voltage in I²C Mode as shown in the Typical Connection Diagram. SDA/CDIN 16 Serial Control Port Data (Input/Output) - SDA is a data I/O line in I²C Mode and is open drain, requiring an external pull-up resistor to the logic interface voltage, as shown in the Typical Con- nection Diagram; CDIN is the input data line for the control port interface in SPI Mode. AD0/CS 17 Address Bit 0 (I²C) / Control Port Chip Select (SPI) (Input) - AD0 is a chip address pin in I²C Mode; CS is the chip-select signal for SPI Mode. TST 10, 12 Test - These pins need to be tied to analog ground. DSD Definitions DSDA1 DSDB1 DSDA2 DSDB2 DSDA3 DSDB3 3 2 1 48 47 46 Direct Stream Digital Input (Input) - Input for Direct Stream Digital serial audio data. GND if unused. DSD_SCLK 42 DSD Serial Clock (Input) - Serial clock for the Direct Stream Digital serial audio interface. Pin Name # Pin Description |
Аналогичный номер детали - CS4365-CQZ |
|
Аналогичное описание - CS4365-CQZ |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |