 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
TMP19A43CZXBG датащи(PDF) 9 Page - Toshiba Semiconductor |
|
||||||||||||||||||||||||||||||
TMP19A43CZXBG датащи(HTML) 9 Page - Toshiba Semiconductor |
|
|
9 / 523 page  TMP19A43 Table 2-3 Pin Names and Functions (2 of 6) Pin name Number of pins Input or output Function P43 1 Input/output Port 43: Input/output port (with pull-up) CS3 Output Chip select 3: "0" is output if the address is in a designated address area. KEY27 Input KEY on wake up input 27: (Dynamic pull up is selectable) Input with Schmitt trigger with Noise filter P44 1 Input/output Port 44: Input/output port (with pull-up) SCOUT Output System clock output: Selectable between high- and low-speed clock outputs, as in the case of CPU P45 1 Input/output Port 45: Input/output port (with pull-up) BUSMD Input Pin for setting an external bus mode: This pin functions as a multiplexed bus by sampling the "H (DVCC3) level" at the rise of a reset signal. It also functions as a separate bus by sampling "L" at the rise of a reset signal. When performing a reset operation, pull it up or down according to a bus mode to be used. Input with Schmitt trigger. (After a reset operation is performed, it can be used as a port.) P46 1 Input/output Port 46: Input/output port (with pull-up) ENDIAN Input This pin is used to set a mode. It performs a big-endian operation by sampling the "H (DVCC3) level" at the rise of a reset signal, and performs a little-endian operation by sampling "L" at the rise of a reset signal. When performing a reset operation, pull it up or down according to the type of endian to be used. (After a reset operation is performed, it can be used as a port.) Input with Schmitt trigger P47 1 Input/output Port 47: Input/output port (with pull-up) TBFOUT Output 16-bit timer F output: Pin for outputting a 16-bit timer F P50-P53 4 Input/output Port 5: Input/output port (with pull-up) that allows input/output to be set in units of bits A0-A3 Output Address: Address buses 0 to 3 (separate bus mode) INTC-INTF Input Interrupt request pins C to F: Selectable between "H" level, "L" level, rising edge, and falling edge Input pin with Schmitt trigger with Noise filter P54,P55 2 Input/output Port 5: Input/output port (with pull-up) that allows input/output to be set in units of bits A4,A5 Output Address: Address buses 4 and 5 (separate bus mode) TB0OUT Output 16-bit timer 0 output: Pin for outputting a 16-bit timer 0 TB1OUT Output 16-bit timer 1 output: Pin for outputting a 16-bit timer 1 P56,P57 2 Input/output Port 5: Input/output port (with pull-up) that allows input/output to be set in units of bits A6,A7 Output Address: Address buses 6 and 7 (separate bus mode) TB2OUT Output 16-bit timer 2 output: Pin for outputting a 16-bit timer 2 TB3OUT Output 16-bit timer 3 output: Pin for outputting a 16-bit timer 3 KEY28,KEY29 Input KEY on wake up input 28 and 29: (Dynamic pull up is selectable) Input pin with Schmitt trigger with Noise filter P60 1 Input/output Port 60: Input/output port (with pull-up) A8 Output Address: Address bus 8 (separate bus mode) TXD0 Output Sending serial data 0: Open drain output pin depending on the program used P61 1 Input/output Port 61: Input/output port (with pull-up) A9 Output Address: Address bus 9 (separate bus mode) RXD0 Input Receiving serial data 0 INTA Input Interrupt request pin A: Selectable between "H" level, "L" level, rising edge, falling edge, and both rising and falling edges. Input pin with Schmitt trigger with Noise filter P62 1 Input/output Port 62: Input/output port (with pull-up) A10 Output Address: Address bus 10 (separate bus mode) SCLK0 Input/output Serial clock input/output 0 CTS0 Input Handshake input pin Open drain output pin depending on the program used P63 1 Input/output Port 63: Input/output port (with pull-up) A11 Output Address: Address bus 11 (separate bus mode) TXD1 Output Sending serial data 1: Open drain output pin depending on the program used P64 1 Input/output Port 64: Input/output port (with pull-up) A12 Output Address: Address bus 12 (separate bus mode) RXD1 Input Receiving serial data 1 INTB Input Interrupt request pin B: Selectable between "H" level, "L" level, rising edge, falling edge, and both rising and falling edges. Input pin with Schmitt trigger with Noise filter TMP19A43 (rev2.0) 2-4 Pin Layout and Pin Functions |
Аналогичный номер детали - TMP19A43CZXBG |
|
Аналогичное описание - TMP19A43CZXBG |
|
|
ссылки URL |
| Конфиденциальность |
| ALLDATASHEETRU.COM |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
