поискавой системы для электроныых деталей |
|
ST24W04M5TR датащи(PDF) 10 Page - STMicroelectronics |
|
ST24W04M5TR датащи(HTML) 10 Page - STMicroelectronics |
10 / 16 page The sequence is as follows: – Initial condition: a Write is in progress (see Figure 8). – Step 1: the Master issues a START condition followed by a Device Select byte (1st byte of the new instruction). – Step 2: if the memory is busy with the internal write cycle, no ACK will be returned and the master goes back to Step 1. If the memory has terminated the internal write cycle, it will re- spond with an ACK, indicating that the memory is ready to receive the second part of the next instruction (the first byte of this instruction was already sent during Step 1). Write Protection. Data in the upper block of 256 bytes of the memory may be write protected. The memory is write protected between a boundary address and the top of memory (address 1FFh) when the PRE input pin is taken high and when the Protect Flag (bit b2 in location 1FFh) is set to ’0’. The boundary address is user defined by writing it in the Block Address Pointer. The Block Address Pointer is an 8 bit EEPROM register located at the address 1FFh. It is composed by 5 MSBs Address Pointer, which defines the bottom boundary ad- dress, and 3 LSBs which must be programmed at DEVICE OPERATION (cont’d) ’0’. This Address Pointer can therefore address a boundary in steps of 8 bytes. The sequence to use the Write Protected feature is: – write the data to be protected into the top of the memory, up to, but not including, location 1FFh; – set the protection by writing the correct bottom boundary address in the Address Pointer (5 MSBs of location 1FFh) with bit b2 (Protect flag) set to ’0’. Note that for a correct fonctionality of the memory, all the 3 LSBs of the Block Address Pointer must also be programmed at ’0’. The area will now be protected when the PRE input pin is taken High. While the PRE input pin is read at ’0’ by the memory, the location 1FFh can be used as a normal EEPROM byte. Caution: Special attention must be used when using the protect mode together with the Multibyte Write mode (MODE input pin High). If the Multibyte Write starts at the location right below the first byte of the Write Protected area, then the instruction will write over the first 3 bytes of the Write Protected area. The area protected is therefore smaller than the content defined in the location 1FFh, by 3 bytes. This does not apply to the Page Write mode as the address counter ’roll-over’ and thus cannot go above the 8 bytes lower boundary of the protected area. BYTE WRITE DEV SEL BYTE ADDR DATA IN MULTIBYTE AND PAGE WRITE DEV SEL BYTE ADDR DATA IN 1 DATA IN 2 AI00793 DATA IN N ACK ACK ACK R/W ACK ACK ACK R/W ACK ACK Figure 9. Write Modes Sequence (ST24/25C04) 10/16 ST24/25C04, ST24/25W04 |
Аналогичный номер детали - ST24W04M5TR |
|
Аналогичное описание - ST24W04M5TR |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |