поискавой системы для электроныых деталей |
|
TC621CCPA датащи(PDF) 3 Page - TelCom Semiconductor, Inc |
|
TC621CCPA датащи(HTML) 3 Page - TelCom Semiconductor, Inc |
3 / 6 page 2-17 TELCOM SEMICONDUCTOR, INC. 7 6 5 4 3 1 2 8 DETAILED DESCRIPTION The TC620/621 consists of a positive temperature coef- ficient (PTC) temperature sensor, and a dual threshold detector. Temperature setpoint programming is easily ac- complished with external programming resistors from the HIGH SET and LOW SET inputs to VDD. The HIGH LIMIT and LOW LIMIT outputs remain low as long as measured temperature is below setpoint values. As measured tem- perature increases, the LOW LIMIT output is driven high when temperature equals the LOW SET setpoint ( ±3°C max). If temperature continues to climb, the HIGH LIMIT output is driven high when temperature equals the HIGH SET setpoint (Figure 1). The CONTROL (hysteresis) output is latched in its active state at the temperature specified by the HIGH SET resistor. CONTROL is maintained active until temperature falls to the value specified by the LOW SET resistor. Programming The TC620 The resistor values to achieve the desired trip-point temperatures on HIGH SET and LOW SET are calculated using EQUATION 1 below: RTRIP = 0.5997 x T 2.1312 Where: Rtrip = Programming resistor in Ohms T = The desired trip point temperature in degrees Kelvin Equation 1. For example, a 50 °C setting on either the HIGH SET or LOW SET input is calculated using Equation 1 as follows: Rset = 0.5997 x ((50 + 273.15)2.1312) = 133.6k Ω Care must be taken to ensure the LOW SET program- ming resistor is a smaller value than the HIGH SET program- ming resistor. Failure to do this will result in erroneous operation of the CONTROL output. Care must also be taken to ensure the LOW SET temperature setting is at least 5 °C lower than the HIGH SET temperature setting. That is: LOW SET ≤ HIGH SET – 5°C The nomograph of Figure 2 can help the user obtain an estimate of the external resistor values required for the desired LOW SET and HIGH SET trip points. Built-in Hysteresis To prevent output "chattering" when measured tem- perature is at (or near) the programmed trip point values, the LOW SET and HIGH SET inputs each have built-in hyster- esis of – 2 °C below the programmed settings (Figure 3). Figure 3: Built-in Hysteresis on Low Limit and High Limit Outputs As shown, the outputs remain in their active state (hysteresis) until temperature falls an additional 2 °C below the user's setting. TEMPERATURE ( °C) -55 -35 -15 5 25 45 65 85 105 125 50 100 150 200 250 SET POINT (SET POINT – 2 °C) HIGH LIMIT or LOW LIMIT Output Figure 1: TC620/621 Input vs. Output Logic LOW SET POINT HIGH SET POINT LOW LIMIT OUTPUT HIGH LIMIT OUTPUT CONTROL OUTPUT (COOL OPTION) CONTROL OUTPUT (HEAT OPTION) TEMPERATURE Figure 2. TC620 Sense Resistors vs. Trip Temperature TC620 TC621 5V, DUAL TRIP POINT TEMPERATURE SENSORS |
Аналогичный номер детали - TC621CCPA |
|
Аналогичное описание - TC621CCPA |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |