uA9636AC

DUAL LINE DRIVER WITH ADJUSTABLE SLEW RATE

SLLS110B – OCTOBER 1980 – REVISED MAY 1995

3

POST OFFICE BOX 655303

electrical characteristics over recommended ranges of free-air temperature, supply voltage, and

wave-shaping resistance (unless otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP†

MAX

UNIT

VIK

Input clamp voltage

II = – 15 mA

– 1.1

– 1.5

V

RL = ∞

5

5.6

6

VOH

High-level output voltage

VI = 0.8 V

RL = 3 kΩ to GND

5

5.6

6

V

RL = 450 Ω to GND

4

5.4

6

RL = ∞

–6‡

– 5.7

–5

VOL

Low-level output voltage

VI = 2 V

RL = 3 kΩ to GND

–6‡

– 5.6

–5

V

RL = 450 Ω to GND

–6‡

– 5.4

–4

IIH

High level input current

VI = 2.4 V

10

µA

IIH

High-level input current

VI = 5.5 V

100

µA

IIL

Low-level input current

VI = 0.4 V

–20

–80

µA

IO

Output current (power off)

VCC

± = 0,

VO = ± 6 V

±100

µA

IOS

Short circut output current§

VI = 2 V

15

25

150

mA

IOS

Short-circut output current§

VI = 0

–15

–40

– 150

mA

rO

Output resistance

RL = 450 Ω

25

50

Ω

ICC

Positive supply current

VCC = ± 12 V,

VI = 0,

13

18

mA

ICC +

Positive supply current

CC

,

R(WS) = 100 kΩ,

I

,

Output open

13

18

mA

ICC

Negative supply current

VCC = ± 12 V,

VI = 0,

13

18

mA

ICC –

Negative supply current

CC

R(WS) = 100 kΩ,

I

Output open

– 13

– 18

mA

† All typical values are at VCC = ±12 V, TA = 25°C.

‡ The algebraic convention, in which the less-positive (more-negative) limit is designated as minimum, is used in this data sheet for logic voltage

levels, e.g., when – 5 V is the maximum, the minimum is a more-negative voltage.

§ Not more than one output should be shorted to ground at a time.

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

R(WS) = 10 kΩ

0.8

1.1

1.4

tTLH

Transition time low to high level output

RL = 450 kΩ

CL =30 pF

R(WS) = 100 kΩ

8

11

14

µs

tTLH

Transition time, low- to high-level output

RL = 450 kΩ,

CL = 30 pF

R(WS) = 500 kΩ

40

55

70

µs

R(WS) = 1 MΩ

80

110

140

R(WS) = 10 kΩ

0.8

1.1

1.4

tTHL

Transition time high to low level output

RL = 450 kΩ

CL =30 pF

R(WS) = 100 kΩ

8

11

14

µs

tTHL

Transition time, high- to low-level output

RL = 450 kΩ,

CL = 30 pF

R(WS) = 500 kΩ

40

55

70

µs

R(WS) = 1 MΩ

80

110

140