поискавой системы для электроныых деталей |
|
BD3539NUX датащи(PDF) 8 Page - Rohm |
|
BD3539NUX датащи(HTML) 8 Page - Rohm |
8 / 12 page BD3539FVM,BD3539NUX Technical Note 8/11 www.rohm.com 2009.10 - Rev.A © 2009 ROHM Co., Ltd. All rights reserved. ● Note for Use 1.Absolute maximum ratings For the present product, thoroughgoing quality control is carried out, but in the event that applied voltage, working temperature range, and other absolute maximum rating are exceeded, the present product may be destroyed. Because it is unable to identify the short mode, open mode, etc., if any special mode is assumed, which exceeds the absolute maximum rating, physical safety measures are requested to be taken, such as fuses, etc. 2.GND potential Bring the GND terminal potential to the minimum potential in any operating condition. 3.Thermal design Consider allowable loss (Pd) under actual working condition and carry out thermal design with sufficient margin provided. 4.Terminal-to-terminal short-circuit and erroneous mounting When the present IC is mounted to a printed circuit board, take utmost care to direction of IC and displacement. In the event that the IC is mounted erroneously, IC may be destroyed. In the event of short-circuit caused by foreign matter that enters in a clearance between outputs or output and power-GND, the IC may be destroyed. 5.Operation in strong electromagnetic field The use of the present IC in the strong electromagnetic field may result in maloperation, to which care must be taken. 6.Built-in thermal shutdown protection circuit The present IC incorporates a thermal shutdown protection circuit (TSD circuit). The working temperature is 175°C (standard value) and has a -15°C (standard value) hysteresis width. When the IC chip temperature rises and the TSD circuit operates, the output terminal is brought to the OFF state. The built-in thermal shutdown protection circuit (TSD circuit) is first and foremost intended for interrupt IC from thermal runaway, and is not intended to protect and warrant the IC. Consequently, never attempt to continuously use the IC after this circuit is activated or to use the circuit with the activation of the circuit premised. 7.Capacitor across output and GND In the event a large capacitor is connected across output and GND, when Vcc and VIN are short-circuited with 0V or GND for some kind of reasons, current charged in the capacitor flows into the output and may destroy the IC. Use a capacitor smaller than 1000 μF between output and GND. 8.Inspection by set substrate In the event a capacitor is connected to a pin with low impedance at the time of inspection with a set substrate, there is a fear of applying stress to the IC. Therefore, be sure to discharge electricity for every process. As electrostatic measures, provide grounding in the assembly process, and take utmost care in transportation and storage. Furthermore, when the set substrate is connected to a jig in the inspection process, be sure to turn OFF power supply to connect the jig and be sure to turn OFF power supply to remove the jig. 9. Inputs to IC terminals This device is a monolithic IC with P + isolation between P-substrate and each element as illustrated below. This P-layer and the N-layer of each element form a PN junction which works as: ・ a diode if the electric potentials at the terminals satisfy the following relationship; GND>Terminal A>Terminal B, or ・ a parasitic transistor if the electric potentials at the terminals satisfy the following relationship; Terminal B>GND Terminal A. The structure of the IC inevitably forms parasitic elements, the activation of which may cause interference among circuits, and/or malfunctions contributing to breakdown. It is therefore requested to take care not to use the device in such manner that the voltage lower than GND (at P-substrate) may be applied to the input terminal, which may result in activation of parasitic elements. Resistor Transistor (NPN) N N N P + P + P P substrate GND Parasitic element Pin A N N P + P + P P substrate GND Parasitic element Pin B C B E N GND Pin A Parasitic element Pin B Other adjacent elements E B C GND Parasitic element |
Аналогичный номер детали - BD3539NUX |
|
Аналогичное описание - BD3539NUX |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |