поискавой системы для электроныых деталей |
|
TPS40304ADRCT датащи(PDF) 8 Page - Texas Instruments |
|
|
TPS40304ADRCT датащи(HTML) 8 Page - Texas Instruments |
8 / 18 page 5 4 3 2 1 6 7 8 9 10 FB COMP PGOOD EN/SS VDD BOOT HDRV SW LDRV/ OC BP Thermal Pad TPS40304A SLUSA30 – FEBRUARY 2010 www.ti.com DEVICE INFORMATION TERMINAL CONFIGURATION The package is an 10-Pin SON (DRC) package. Note: The thermal pad is an electrical ground connection. PIN FUNCTIONS TERMINAL I/O DESCRIPTION NAME NO. Gate drive voltage for the high-side N-channel MOSFET. A 100 nF capacitor (typical) must be connected BOOT 6 I between this pin and SW. For low input voltage operation, an external schottky diode from BP to BOOT is recommended to maximize the gate drive voltage for the high-side. Output bypass for the internal regulator. Connect a low ESR bypass ceramic capacitor of 1 µF or greater from BP 10 O this pin to GND. COMP 4 O Output of the error amplifier and connection node for loop feedback components. Logic level input which starts or stops the controller via an external user command. Letting this pin float turns the controller on. Pulling this pin low disables the controller. This is also the soft-start programming pin. A capacitor connected from this pin to GND programs the soft-start time. The capacitor is charged with an internal current source of 10 µA. The resulting voltage ramp of this pin is also used as a second non-inverting EN/SS 2 I input to the error amplifier after a 0.8 V (typical) level shift downwards. Output regulation is controlled by the internal level shifted voltage ramp until that voltage reaches the internal reference voltage of 591 mV – the voltage ramp of this pin reaches 1.4 V (typical). Optionally, a 267 k Ω resistor from this pin to BP enables frequency spread spectrum feature. Inverting input to the error amplifier. In normal operation, the voltage on this pin is equal to the internal FB 5 I reference voltage. PGOOD 3 O Open drain power good output. HDRV 7 O Bootstrapped gate drive output for the high-side N-channel MOSFET. Gate drive output for the low-side synchronous rectifier N-channel MOSFET. A resistor from this pin to GND LDRV/OC 9 O is also used to determine the voltage level for OCP. An internal current source of 10 µA flows through the resistor during initial calibration and that sets up the voltage trip point used for OCP. Power input to the controller. Bypass VDD to GND with a low ESR ceramic capacitor of at least 1.0-µF close VDD 1 I to the device. Sense line for the adaptive anti-cross conduction circuitry. Serves as common connection for the flying SW 8 O high-side FET driver. Ground connection to the controller. This is also the thermal pad used to conduct heat from the device. This Thermal connection serves a twofold purpose. The first is to provide an electrical ground connection for the device. GND Pad The second is to provide a low thermal impedance path from the device die to the PCB. This pad should be tied externally to a ground plane. 8 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s) :TPS40304A |
Аналогичный номер детали - TPS40304ADRCT |
|
Аналогичное описание - TPS40304ADRCT |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |