поискавой системы для электроныых деталей |
|
BA6950FS датащи(PDF) 6 Page - Rohm |
|
BA6950FS датащи(HTML) 6 Page - Rohm |
6 / 11 page Technical Note 6/10 BA6950FS, BA6951FS www.rohm.com 2011.05 - Rev.C © 2011 ROHM Co., Ltd. All rights reserved. ● External application components 1) Resistor for the current sensing, R5 This is a current sensing resistor, care must be taken to avoid changes in the ground wire pattern in any external connected component. 2) Control amplifier gain setting resistor, R1 VCTL pin voltage is buffered to RC pin, and the control gain - VCTLGA - can be set by connecting R1. The current decided here is output to RT1 pin. 3) Control amplifier phase compensation capacitor, C1 This phase compensation capacitor for the control amplifier. Please monitor the RT1 pin voltage and confirm no oscillation. About 33pF is recommended. 4) Current feedback amplifier gain setting resistor, R4 CS1 pin voltage (the motor current detection) is buffered to CS2 pin - BA6950FS. ATC pin voltage (the motor current detection) is buffered to CS pin - BA6951FS. The current feedback gain can be set by R4 connecting to CS2 or CS pin. The current decided here is output to RT2 pin. 5) Pre-amplifier gain setting resistor, R2, R3 These resistors are to add the control amplifier output and the current feedback amplifier output. This amplifier has about fourfold gain. 6) Pre-amplifier phase compensation capacitor, C2 Please connect the capacitor about 0.1µF as the phase compensation of the pre-amplifier, and monitor the driver output no oscillation. 7) Stabilization capacitor for the power supply line, C5, C6 Please connect the capacitor of 1μF to 100μF for the stabilization of the power supply line, and confirm the motor operation. 8) Phase compensating capacitor, C3, C4 Noise is generated in output pins or oscillation results in accord with the set mounting state such as power supply circuit, motor characteristics, PCB pattern artwork, etc. As noise oscillation measures, connect 0.01μF to 0.1μF capacitors. 9) Torque limiter setting, TL pin, BA6951FS only The motor current is limited so that ATC pin voltage should not exceed TL pin voltage. ● Functional descriptions Table 3 Logic table FIN RIN M1 M2 Operation L L OPEN* OPEN* Stop (idling) H L L H Forward (M2 > M1) L H H L Reverse (M1 > M2) H H L L Brake (stop) * OPEN is the off state of all output transistors. Please note that this is the state of the connected diodes, which differs from that of the mechanical relay. |
Аналогичный номер детали - BA6950FS_11 |
|
Аналогичное описание - BA6950FS_11 |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |