поискавой системы для электроныых деталей |
|
AD7870AJN датащи(PDF) 7 Page - Analog Devices |
|
AD7870AJN датащи(HTML) 7 Page - Analog Devices |
7 / 12 page AD7870A –7– REV. 0 Figure 6. Full-Scale Adjust Circuit Positive Full-Scale Adjust Apply a voltage of 2.9978 V (FS/2 – 3/2 LSBs) at V1. Adjust R2 until the ADC output code flickers between 0111 1111 1110 and 0111 1111 1111. Negative Full-Scale Adjust Apply a voltage of –2.9993 V (–FS/2 +1/ 2 LSB) at V1 and adjust R2 until the ADC output code flickers between 1000 0000 0000 and 1000 0000 0001. UNIPOLAR OPERATION A typical unipolar circuit is shown in Figure 7. The AD7870A REF OUT is used to offset the analog input by 3 V. The ana- log input range is determined by the ratio of R3 to R4. The minimum range with which the circuit will work is 0 V to +3 V (R3 = 0, R4 = O/C). The resistor values are given in Figure 7 for input ranges of 0 V to +5 V and 0 V to +10 V. R5 and R6 are included for offset and full-scale adjust only and should be omitted if adjustment is not required. Figure 7. Unipolar Circuit The ideal input/output transfer function is shown in Figure 8. The output can be converted to natural binary by inverting the MSB. Figure 8. Unipolar Transfer Function UNIPOLAR OFFSET AND FULL-SCALE ADJUSTMENT When absolute accuracy is required, offset and full-scale error can be adjusted to zero. Offset must be adjusted before full scale. This is achieved by applying an input voltage of (1/2 LSB) to Vl and adjust R6 until the ADC output code flickers between 1000 0000 0000 and 1000 0000 0001. For full-scale adjust- ment, apply an input voltage of (FS–3/2 LSBs) to Vl and adjust R5 until the output code flickers between 0111 1111 1110 and 0111 11111111. TIMING AND CONTROL The AD7870A is capable of one basic interfacing mode. In this mode (Mode 1), the CONVST line is used to start conversion and drive the track/hold into its hold mode. At the end of con- version the track/hold returns to its tracking mode. It is princi- pally intended for digital signal processing and other applications where precise sampling in time is required. In these applica- tions, it is important that the signal sampling occurs at exactly equal intervals to minimize errors due to sampling uncertainty or jitter. For these cases, the CONVST line is driven by a timer or some precise clock source. DATA OUTPUT FORMATS The AD7870A offers a choice of three data output formats, one serial and two parallel. The parallel data formats are a single, 12-bit parallel word for 16-bit data buses and a two-byte format for 8-bit data buses. The data format is controlled by the 12/ 8/CLK input. A logic high on this pin selects the 12-bit par- allel output format only. A logic low or –5 V applied to this pin allows the user access to either serial or byte formatted data. Three of the pins previously assigned to the four MSBs in paral- lel form are now used for serial communications while the fourth pin becomes a control input for the byte-formatted data. |
Аналогичный номер детали - AD7870AJN |
|
Аналогичное описание - AD7870AJN |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |