поискавой системы для электроныых деталей |
|
DAC0832LCN датащи(PDF) 6 Page - Texas Instruments |
|
DAC0832LCN датащи(HTML) 6 Page - Texas Instruments |
6 / 29 page DAC0830, DAC0832 SNAS534B – MAY 1999 – REVISED MARCH 2013 www.ti.com is high. WR2: Write 2 (active low). This signal, in combination with XFER, causes the 8-bit data which is available in the input latch to transfer to the DAC register. XFER: Transfer control signal (active low). The XFER will enable WR2. Other Pin Functions DI0-DI7: Digital Inputs. DI0 is the least significant bit (LSB) and DI7 is the most significant bit (MSB). IOUT1: DAC Current Output 1. IOUT1 is a maximum for a digital code of all 1's in the DAC register, and is zero for all 0's in DAC register. IOUT2: DAC Current Output 2. IOUT2 is a constant minus IOUT1 , or IOUT1 + IOUT2 = constant (I full scale for a fixed reference voltage). Rfb: Feedback Resistor. The feedback resistor is provided on the IC chip for use as the shunt feedback resistor for the external op amp which is used to provide an output voltage for the DAC. This on-chip resistor should always be used (not an external resistor) since it matches the resistors which are used in the on-chip R-2R ladder and tracks these resistors over temperature. VREF: Reference Voltage Input. This input connects an external precision voltage source to the internal R-2R ladder. VREF can be selected over the range of +10 to −10V. This is also the analog voltage input for a 4- quadrant multiplying DAC application. VCC: Digital Supply Voltage. This is the power supply pin for the part. VCC can be from +5 to +15VDC. Operation is optimum for +15VDC GND: The pin 10 voltage must be at the same ground potential as IOUT1 and IOUT2 for current switching applications. Any difference of potential (VOS pin 10) will result in a linearity change of : (1) For example, if VREF = 10V and pin 10 is 9mV offset from IOUT1 and IOUT2 the linearity change will be 0.03%. Pin 3 can be offset ±100mV with no linearity change, but the logic input threshold will shift. Linearity Error Figure 3. a) End Point Test After Figure 4. b) Best Straight Line Figure 5. c) Shifting fs adj. to Zero and fs adj. Pass Best Straight Line Test Definition of Terms Resolution: Resolution is directly related to the number of switches or bits within the DAC. For example, the DAC0830 has 28 or 256 steps and therefore has 8-bit resolution. Linearity Error: Linearity Error is the maximum deviation from a straight line passing through the endpoints of the DAC transfer characteristic. It is measured after adjusting for zero and full-scale. Linearity error is a parameter intrinsic to the device and cannot be externally adjusted. 6 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated Product Folder Links: DAC0830 DAC0832 |
Аналогичный номер детали - DAC0832LCN |
|
Аналогичное описание - DAC0832LCN |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |