поискавой системы для электроныых деталей |
|
UC3717AQ датащи(PDF) 6 Page - Texas Instruments |
|
UC3717AQ датащи(HTML) 6 Page - Texas Instruments |
6 / 12 page Low-pass filter components RC CC should be selected so that all switching transients from the power transistors and commutating diodes are well smoothed, but the pri- mary signal, which can be in the range of 1/TOFF or higher must be passed. Figure 5A shows the waveform which must be smoothed, Figure 5B presents the desired waveform that just smoothes out overshoot without radi- cal distortion. The sense resistor should be chosen as small as practi- cal to allow as much of the winding supply voltage to be used as overdrive to the motor winding. VRS, the voltage across the sense resistor, should not exceed 1.5V. Voltage Overdrive: In many applications, maximum speed or step rate is a desirable performance charac- teristic. Maximum step rate is a direct function of the time necessary to reverse winding current with each step. In response to a constant motor supply voltage, the winding current changes exponentially with time, whose shape is determined by the winding time constant and expressed as: Im = Vm R [1 −EXP (−RT⁄L)] as presented in Figure 9. With rated voltage applied, the time required to reach rated current is excessive when compared with the time required with over-voltage ap- plied, even though the time constant L/R remains con- stant. With over-voltage however, the final value of current is excessive and must be prevented. This is ac- complished with switch drive by repetitively switching the sink drivers on and off, so as to maintain an average value of current equal to the rated value. This results in a small amount of ripple in the controlled current, but the increase in step rate and performance may be consider- able. Interference: Electrical noise generated by the chopping action can cause interference problems, particularly in the vicinity of magnetic storage media. With this in mind, printed circuit layouts, wire runs and decoupling must be considered. 0.01 to 0.1 µF ceramic capacitors for high fre- quency bypass located near the drive package across V+ and ground might be very helpful. The connection and ground leads of the current sensing components should be kept as short as possible. Half-Stepping: In half step sequence the power input to the motor alternates between one or two phases being energized. In a two phase motor the electrical phase shift between the windings is 90°. The torque developed is the vector sum of the two windings energized. Therefore when only one winding is energized the torque of the mo- tor is reduced by approximately 30%. This causes a torque ripple and if it is necessary to compensate for this, the VR input can be used to boost the current of the sin- gle energized winding. Figure 9. With rated voltage applied, winding current does not exceed rated value, but takes L/R seconds to reach 63% of its final value - probably too long. Increased performance requires an increase in applied volt- age, of overdrive, and therefore a means to limit current. The UC3717A motor driver performs this task effi- ciently. UC3717A FUNCTIONAL DESCRIPTION (cont.) 6 |
Аналогичный номер детали - UC3717AQ |
|
Аналогичное описание - UC3717AQ |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |