поискавой системы для электроныых деталей |
|
SM15T15A датащи(PDF) 2 Page - General Semiconductor |
|
SM15T15A датащи(HTML) 2 Page - General Semiconductor |
2 / 3 page ELECTRICAL CHARACTERISTICS RATINGS at (TA=25ºC unless otherwise noted) SM15T6V8A GDE7 GDE7 5.80 1000 6.45 7.14 10 10.5 143 13.4 746 5.7 SM15T7V5A GDK7 BDK7 6.40 500 7.13 7.88 10 11.3 132 14.5 690 6.1 SM15T10A GDT7 BDT7 8.55 10.0 9.50 10.5 1.0 14.5 103 18.6 538 7.3 SM15T12A GDX7 BDX7 10.2 5.00 11.4 12.6 1.0 16.7 90.0 21.7 461 7.8 SM15T15A GEG7 GEG7 12.8 5.00 14.3 15.8 1.0 21.2 71.0 27.2 368 8.4 SM15T18A GEM7 BEM7 15.3 5.00 17.1 18.9 1.0 25.2 59.5 32.5 308 8.8 SM15T22A GET7 BET7 18.8 5.00 20.9 23.1 1.0 30.6 49.0 39.3 254 9.2 SM15T24A GEV7 GEV7 20.5 5.00 22.8 25.2 1.0 33.2 45.0 42.8 234 9.4 SM15T27A GEX7 BEX7 23.1 5.00 25.7 28.4 1.0 37.5 40.0 48.3 207 9.6 SM15T30A GFE7 BFE7 25.6 5.00 28.5 31.5 1.0 41.5 36.0 53.5 187 9.7 SM15T33A GFG7 GFG7 28.2 5.00 31.4 34.7 1.0 45.7 33.0 59.0 169 9.8 SM15T36A GFK7 BFK7 30.8 5.00 34.2 37.8 1.0 49.9 30.0 64.3 156 9.9 SM15T39A GFM7 BFM7 33.3 5.00 37.1 41.0 1.0 53.9 28.0 69.7 143 10.0 SM15T68A GGG7 GGG7 58.1 5.00 64.6 71.4 1.0 92.0 16.3 121 83 10.4 SM15T100A GGV7 GGV7 85.5 5.00 95.0 105 1.0 137 11.0 178 56 10.6 SM15T150A GHK7 GHK7 128 5.00 143 158 1.0 207 7.20 265 38 10.8 SM15T200A GHR7 GHR7 171 5.00 190 210 1.0 274 5.50 353 28 10.8 SM15T220A GHR8 GHR8 188 5.00 209 231 1.0 328 4.60 388 26 10.8 NOTES: (1) For bi-directional devices add “C” for ±10% and “CA” for ±5% tolerance of VBR (2) VBR measured after IT applied for 300µs square wave pulse (3) For bipolar devices with VR=10 Volts or under, the IT limit is doubled APPLICATION NOTES A 1500W (SMC) device is normally selected when the threat of transients is from lightning induced transients, conducted via external leads or I/O lines. It is also used to protect against switching transients induced by large coils or industrial motors. Source impedance at component level in a system is usually high enough to limit the current within the peak pulse current (IPP) rating of this series. In an overstress condition, the failure mode is a short circuit. RECOMMENDED PAD SIZES The pad dimensions should be 0.010” (0.25mm) longer than the contact size, in the lead axis. This allows a solder fillet to form, see figure below. Contact factory for soldering methods Type(1) Device Marking Code Uni Bi Standoff Voltage VRM (Volts) Leakage Current(3) IRM @ VRM ( µA) Breakdown Voltage VBR @ IT (2) (Volts) Min Max Test Current IT (mA) Clamping Voltage VC @ IPP 10/1000 µs (Volts) (Amps) α T Max 10-4/ °C Clamping Voltage VC @ IPP 8/20 µs (Volts) (Amps) 0.190 (4.83) 0.125 (3.17) 0.070 (1.78) |
Аналогичный номер детали - SM15T15A |
|
Аналогичное описание - SM15T15A |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |