TPA6017A2

SLOS386A − NOVEMBER 2001 − REVISED APRIL 2007

4

www.ti.com

6 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Continuous total power dissipation

internally limited (see Dissipation Rating Table)

. . . . . . . . . . . . . . . . . . . . . . . . . .

−40

°C to 85°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

−40

°C to 150°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

−65

°C to 150°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds

260

°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrostatic discharge

HBM:2 kV typical, CDM:200 V typical

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

DISSIPATION RATING TABLE

PACKAGE

TA ≤ 25°C

DERATING FACTOR

TA = 70°C

TA = 85°C

PWP

2.7 W‡

21.8 mW/

°C

1.7 W

1.4 W

‡ See the Texas Instruments document, PowerPAD Thermally Enhanced Package Application Report

(literature number SLMA002), for more information on the PowerPAD

 package. The thermal data was

measured on a PCB layout based on the information in the section entitled Texas Instruments Recommended

Board for PowerPAD

 on page 33 of the before mentioned document.

recommended operating conditions

MIN

MAX

UNIT

Supply voltage, VDD

4.5

5.5

V

High-level input voltage, VIH

SHUTDOWN

2

V

Low-level input voltage, VIL

SHUTDOWN

0.8

V

Operating free-air temperature, TA

−40

85

°C

noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

|VOO|

Output offset voltage (measured differentially)

VI = 0, Av = −2 V/V

25

mV

PSRR

Power supply rejection ratio

VDD = 4.5 V to 5.5 V

77

dB

|IIH|

High-level input current

VDD = 5.5 V,

VI = VDD

1

µA

|IIL|

Low-level input current

VDD = 5.5 V,

VI = 0 V

1

µA

IDD

Supply current

SHUTDOWN = 2 V

6

10

mA

IDD(SD) Supply current, shutdown mode

SHUTDOWN = 0.8 V

150

300

µA