 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
TC7136CKW датащи(PDF) 10 Page - Microchip Technology |
|
||||||||||||||||||||||||||||||
TC7136CKW датащи(HTML) 10 Page - Microchip Technology |
|
|
10 / 22 page  TC7136/TC7136A DS21461B-page 10 © 2002 Microchip Technology Inc. 4.0 ANALOG SECTION In addition to the basic integrate and de-integrate dual slope cycles discussed above, the TC7136 and TC7136A designs incorporate an "integrator output zero cycle" and an "auto-zero cycle." These additional cycles ensure the integrator starts at 0V (even after a severe over range conversion) and that all offset volt- age errors (buffer amplifier, integrator and comparator) are removed from the conversion. A true digital zero reading is assured without any external adjustments. A complete conversion consists of four distinct phases: 1. Integrator output zero phase 2. Auto-zero phase 3. Signal integrate phase 4. Reference de-integrate phase 4.1 Integrator Output Zero Phase This phase ensures the integrator output is at 0V before the system zero phase is entered. This ensures that true system offset voltages will be compensated for, even after an over range conversion. The count for this phase is a function of the number of counts required by the de-integrate phase. The count lasts from 11 to 140 counts for non over range conversions and from 31 to 640 counts for over range conversions. 4.2 Auto-Zero Phase During the auto-zero phase, the differential input signal is disconnected from the circuit by opening internal analog gates. The internal nodes are shorted to analog common (ground) to establish a zero input condition. Additional analog gates close a feedback loop around the integrator and comparator. This loop permits com- parator offset voltage error compensation. The voltage level established on CAZ compensates for device offset voltages. The auto-zero phase residual is typically 10 µVto15µV. The auto-zero duration is from 910 to 2900 counts for non over range conversions and from 300 to 910 counts for over range conversions. 4.3 Signal Integration Phase The auto-zero loop is entered and the internal differen- tial inputs connect to VIN+ and VIN-. The differential input signal is integrated for a fixed time period. The TC7136/A signal integration period is 1000 clock peri- ods or counts. The externally set clock frequency is divided by four before clocking the internal counters. The integration time period is: EQUATION 4-1: The differential input voltage must be within the device Common mode range when the converter and mea- sured system share the same power supply common (ground). If the converter and measured system do not share the same power supply common, VIN- should be tied to analog common. Polarity is determined at the end of signal integrate phase. The sign bit is a true polarity indication, in that signals less than 1LSB are correctly determined. This allows precision null detection, limited only by device noise and auto-zero residual offsets. 4.4 Reference Integrate Phase The third phase is reference integrate or de-integrate. VIN- is internally connected to analog common and VIN+ is connected across the previously charged refer- ence capacitor. Circuitry within the chip ensures that the capacitor will be connected with the correct polarity to cause the integrator output to return to zero. The time required for the output to return to zero is propor- tional to the input signal and is between 0 and 2000 internal clock periods. The digital reading displayed is: EQUATION 4-2: FIGURE 4-1: CONVERSION TIMING DURING NORMAL OPERATION FIGURE 4-2: CONVERSION TIMING DURING OVER RANGE OPERATION tSI = x 1000 4 FOSC Where FOSC = external clock frequency. 1000 V IN V REF ---------------- = INT DENT ZI AZ 4000 910-2900 1-2000 1000 11-140 AZ 4000 ZI DEINT INT 1000 2001-2090 31-640 300-910 |
Аналогичный номер детали - TC7136CKW |
|
Аналогичное описание - TC7136CKW |
|
|
|
ссылки URL |
| Конфиденциальность |
| ALLDATASHEETRU.COM |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
