поискавой системы для электроныых деталей |
|
AD7873ACPZ3 датащи(PDF) 7 Page - Analog Devices |
|
AD7873ACPZ3 датащи(HTML) 7 Page - Analog Devices |
7 / 28 page AD7873 Rev. D | Page 7 of 28 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS AD7873 TOP VIEW (Not to Scale) 1 2 3 4 12 11 10 9 16 15 14 13 56 7 8 PIN 1 INDICATOR AUX VREF +VCC PENIRQ Y+ X+ +VCC DCLK Figure 3. LFCSP Pin Configuration 1 2 3 4 5 6 7 10 8 9 11 12 13 14 15 16 AD7873 TOP VIEW (Not to Scale) +VCC X+ Y+ X– Y– GND VBAT AUX DCLK CS DIN BUSY DOUT PENIRQ +VCC VREF Figure 4.QSOP/TSSOP Pin Configuration Table 4. Pin Function Descriptions Mnemonic Function +VCC Power Supply Input. The +VCC range for the AD7873 is from 2.2 V to 5.25 V. Both +VCC pins should be connected directly together. X+ X+ Position Input. ADC Input Channel 1. Y+ Y+ Position Input. ADC Input Channel 2. X– X– Position Input. Y– Y– Position Input. ADC Input Channel 3. GND Analog Ground. Ground reference point for all circuitry on the AD7873. All analog input signals and any external reference signals should be referred to this GND voltage. VBAT Battery Monitor Input. ADC Input Channel 4. AUX Auxiliary Input. ADC Input Channel 5. VREF Reference Output for the AD7873. Alternatively an external reference can be applied to this input. The voltage range for the external reference is 1.0 V to +VCC. For specified performance, it is 2.5 V on the AD7873. The internal 2.5 V reference is available on this pin for use external to the device. The reference output must be buffered before it is applied elsewhere in a system. A 0.1 µF capacitor is recommended between this pin and GND to reduce system noise effects. PENIRQ Pen Interrupt. CMOS logic open drain output (requires 10 kΩ to 100 kΩ pull-up resistor externally). DOUT Data Out. Logic Output. The conversion result from the AD7873 is provided on this output as a serial data stream. The bits are clocked out on the falling edge of the DCLK input. This output is high impedance when CS is high. BUSY BUSY Output. Logic Output. This output is high impedance when CS is high. DIN Data In. Logic Input. Data to be written to the AD7873 control register is provided on this input and is clocked into the register on the rising edge of DCLK (see the Control Register section). CS Chip Select Input. Active Low Logic Input. This input provides the dual function of initiating conversions on the AD7873 and enabling the serial input/output register. DCLK External Clock Input. Logic Input. DCLK provides the serial clock for accessing data from the part. This clock input is also used as the clock source for the AD7873 conversion process. |
Аналогичный номер детали - AD7873ACPZ3 |
|
Аналогичное описание - AD7873ACPZ3 |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |