поискавой системы для электроныых деталей
  Russian  ▼
ALLDATASHEETRU.COM

X  

LM1865M датащи(PDF) 7 Page - National Semiconductor (TI)

[Old version datasheet] Texas Instruments acquired National semiconductor.
номер детали LM1865M
подробное описание детали  Advanced FM IF System
Download  16 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
производитель  NSC [National Semiconductor (TI)]
домашняя страница  http://www.national.com
Logo NSC - National Semiconductor (TI)

LM1865M датащи(HTML) 7 Page - National Semiconductor (TI)

Back Button LM1865M Datasheet HTML 3Page - National Semiconductor (TI) LM1865M Datasheet HTML 4Page - National Semiconductor (TI) LM1865M Datasheet HTML 5Page - National Semiconductor (TI) LM1865M Datasheet HTML 6Page - National Semiconductor (TI) LM1865M Datasheet HTML 7Page - National Semiconductor (TI) LM1865M Datasheet HTML 8Page - National Semiconductor (TI) LM1865M Datasheet HTML 9Page - National Semiconductor (TI) LM1865M Datasheet HTML 10Page - National Semiconductor (TI) LM1865M Datasheet HTML 11Page - National Semiconductor (TI) Next Button
Zoom Inzoom in Zoom Outzoom out
 7 / 16 page
background image
Application Notes
ADJUSTABLE MUTESTOP THRESHOLD
The threshold adjustments for the mute and stop functions
are controlled by the same pins Thus the term mutestop
will be used to designate either function
The adjustable mutestop threshold in the LM1865 allows
for user programming of the signal level at which muting or
stop indication takes place The adjustment can be made in
two mutually exclusive ways The first way is to take a volt-
age divider from the meter output (pin 8) to the off channel
mute input (pin 13) When the voltage at pin 13 falls below
022V an internal comparator is tripped causing muted or
causing the stop output to go low Adjustment of the voltage
divider ratio changes the signal level at which this happens
The second method of mutestop detection as a function of
signal level is to use the presence of ultrasonic noise in the
recovered audio to trip the internal comparator As the sig-
nal level at the antenna of the radio drops the amount of
noise in the recovered audio both audible and ultrasonic
increases
The recovered audio is internally coupled through a high
pass filter to pin 13 which is internally biased above the
comparator trip point Large negative-going noise spikes will
drive pin 13 below the comparator trip point and cause
mutestop action A simplified circuit is shown in
Figure 4
Since the input to the comparator is noise the output of the
comparator is noise Consequently a mutestop filter on pin
12 is required to convert output noise spikes to an average
DC value This filter is not necessary if pin 13 is driven from
the meter
Adjustment of the mutestop threshold in the noise mode is
accomplished by adjusting the pole of the high pass filter
coupled to the comparator input This is done with a series
capacitorresistor combination R9 C11 from pin 13 to
ground As the pole is moved higher in frequency (ie R9
gets smaller) more ultrasonic noise is required in the recov-
ered audio in order to initiate mutestop action This corre-
sponds to a weaker signal at the antenna of the radio In
choosing the correct value for R9 it is important to make
sure that recovered audio below 75 kHz is not sufficient to
cause mutestop action This is because stereo and SCA
information are contained in the audio signal up to 75 kHz
Also note that the ultrasonic mutestop circuit will not oper-
ate properly unless a tuner is connected to the IF This is
because at low signal levels the noise at the tuner output
dominates any noise sources in the IC Consequently driv-
ing the IC directly with a 50X generator is much less noisy
than driving the IC with a tuner and therefore not realistic
The RC filter on pin 12 not only filters out noise from the
comparator output but controls the ‘‘feel’’ when manually
tuning For example a very long time constant will cause
the mute to remain active if you rapidly tune through valid
strong stations and will only release the mute if you slowly
tune to a valid station Conversely a short time constant will
allow the mute to kick in and out as one tunes rapidly
through valid stations
The advantage in using the noise mutestop approach ver-
sus the meter driven approach is that the point at which
mutestop action occurs is directly related to the signal-to-
noise ratio in the recovered audio Furthermore the mute
stop threshold is not subject to production and temperature
variations in the meter output voltage at low signal levels
and thus might be able to be set without a production ad-
justment of the radio The noise mutestop threshold is very
insensitive to temperature and gain variations Proper oper-
ation of this circuit requires that the signal level mutestop
threshold be set at a signal level that achieves 45 dB SN
(g3 dB) in mono in a radio In an electronically tuned radio
the signal level stop threshold can be set to a much larger
level by gain reducing the tuner (ie pulling the AGC line) in
scan mode and then releasing the AGC once the radio
stops on a station In an environment where temperature
variations are minimal and manual adjustment of the signal
level mutestop threshold is desired then the meter driven
approach is the best alternative
TLH7509 – 8
FIGURE 4 Simplified Level MuteStop Circuit
7


Аналогичный номер детали - LM1865M

производительномер деталидатащиподробное описание детали
logo
National Semiconductor ...
LM1863 NSC-LM1863 Datasheet
268Kb / 14P
   AM Radio System for Electronically Tuned Radios
LM1863M NSC-LM1863M Datasheet
268Kb / 14P
   AM Radio System for Electronically Tuned Radios
LM1866 NSC-LM1866 Datasheet
257Kb / 7P
   LOW VOLTAGE AM/FM RECEIVER
LM1866N NSC-LM1866N Datasheet
257Kb / 7P
   LOW VOLTAGE AM/FM RECEIVER
LM1868 NSC-LM1868 Datasheet
251Kb / 10P
   Radio System
More results

Аналогичное описание - LM1865M

производительномер деталидатащиподробное описание детали
logo
AUK corp
SL1018 AUK-SL1018_1 Datasheet
220Kb / 9P
   FM IF SYSTEM
logo
Toshiba Semiconductor
TA7761P TOSHIBA-TA7761P Datasheet
1,011Kb / 14P
   FM IF SYSTEM
logo
Rohm
BA4234 ROHM-BA4234 Datasheet
514Kb / 6P
   FM IF SYSTEM
logo
AUK corp
SL1018 AUK-SL1018 Datasheet
293Kb / 9P
   FM IF SYSTEM
logo
Intersil Corporation
CA3089 INTERSIL-CA3089 Datasheet
236Kb / 7P
   FM IF System
November 1996
CA3189 INTERSIL-CA3189 Datasheet
129Kb / 8P
   FM IF System
May 1999
logo
Hitachi Semiconductor
HA12412 HITACHI-HA12412 Datasheet
666Kb / 8P
   FM IF SYSTEM
logo
Intersil Corporation
CA3089 INTERSIL-CA3089_02 Datasheet
459Kb / 8P
   FM IF System
logo
Hitachi Semiconductor
HA11225 HITACHI-HA11225 Datasheet
504Kb / 6P
   FM IF System
logo
Sanyo Semicon Device
LA1231N SANYO-LA1231N Datasheet
665Kb / 8P
   FM IF System
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16


датащи скачать

Go To PDF Page


ссылки URL




Конфиденциальность
ALLDATASHEETRU.COM
Вашему бизинису помогли Аллдатащит?  [ DONATE ] 

Что такое Аллдатащит   |   реклама   |   контакт   |   Конфиденциальность   |   обмен ссыками   |   поиск по производителю
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com