поискавой системы для электроныых деталей |
|
MT9V032 датащи(PDF) 21 Page - ON Semiconductor |
|
MT9V032 датащи(HTML) 21 Page - ON Semiconductor |
21 / 61 page MT9V032 www.onsemi.com 21 Table 8. REGISTER DESCRIPTIONS 0X06 (6) VERTICAL BLANKING 2:0 Scan Mode 0 = Progressive scan. 1 = Not valid. 2 = Two−field Interlaced scan. Even−numbered rows are read first, and followed by odd−numbered rows. 3 = Single−field Interlaced scan. If start address is even number, only even−numbered rows are read out; if start address is odd number, only odd−numbered rows are read out. Effective image size is decreased by half. 0 Y 0, 2, 3 W 3 Sensor Master/Slave Mode 0 = Slave mode. Initiating exposure and readout is allowed. 1 = Master mode. Sensor generates its own exp sure and readout timing according to simultaneous/se- quential mode control bit. 1 Y 0,1 W 4 Sensor Snapshot Mode 0 = Snapshot disabled. 1 = Snapshot mode enabled. The start of frame is triggered by providing a pulse at EXPOSURE pin. Sensor master/ slave mode should be set to logic 1 to turn on this mode. 0 Y 0,1 W 5 Stereoscopy Mode 0 = Stereoscopy disabled. Sensor is stand−alone and the PLL generates a 320 MHz (x12) clock. 1 = Stereoscopy enabled. The PLL generates a 480 MHz (x18) clock. 0 Y 0,1 W 6 Stereoscopic Master/Slave mode 0 = Stereoscopic master. 1 = Stereoscopic slave. Stereoscopy mode should be en- abled when using this bit. 0 Y 0,1 W 7 Parallel Output Enable 0 = Disable parallel output. DOUT(9:0) are in High−Z. 1 = Enable parallel output. 1 Y 0,1 W 8 Simultaneous/ Sequential Mode 0 = Sequential mode. Pixel and column readout takes place only after exposure is complete. 1 = Simultaneous mode. Pixel and column readout takes place in conjunction with exposure. 1 Y 0,1 W 0X08 (8) SHUTTER WIDTH 1 14:0 Shutter Width 1 The row number in which the first knee occurs. This may be used only when high dynamic range option (bit 6 of R0x0F) is enabled and exposure knee point auto adjust control bit is disabled. This register is not shadowed, but any change made does not take effect until the following new frame. 1BB (443) N 1–32767 W 0X09 (9) SHUTTER WIDTH 2 14:0 Shutter Width 2 The row number in which the second knee occurs. This may be used only when high dynamic range option (bit 6 of R0x0F) is enabled and exposure knee point auto adjust control bit is disabled. This register is not shadowed, but any change made does not take effect until the following new frame. Shutter width 2 = (bits 14:0) Note: t1 = Shutter width 1; t2 = Shutter width 2 – Shutter 1; t3 = Total integration – Shutter width 2. 1D9 (473) N 1–32767 W 0X0A (10) SHUTTER WIDTH CONTROL 3:0 T2 Ratio One−half to the power of this value indicates the ratio of duration time t2, when saturation control gate is adjusted to level V2 to total integration when exposure knee point auto adjust control bit is enabled. This register is not shadowed, but any change made does not take effect until the following new frame. t2 = Total integration × (½)t2_ratio. 4 N 0–15 W |
Аналогичный номер детали - MT9V032_17 |
|
Аналогичное описание - MT9V032_17 |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |