поискавой системы для электроныых деталей |
|
TL080 датащи(PDF) 3 Page - Texas Instruments |
|
TL080 датащи(HTML) 3 Page - Texas Instruments |
3 / 13 page TL080 JFET-INPUT OPERATIONAL AMPLIFIER SLOS368 – JUNE 2001 3 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage (see Note 1): VCC+ 18 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC– –18 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Differential input voltage, VID (see Note 2) ±30 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input voltage, VI (see Notes 1 and 3) ±15 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Duration of short-circuit current (see Note 4) Unlimited . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package thermal impedance, θJA (see Notes 5 and 6) 85 °C/W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 260 °C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Storage temperature range, Tstg –65 °C to 150°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC–. 2. Differential voltages are at IN+ with respect to IN–. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less. 4. The output can be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. 5. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can impact reliability. 6. The package thermal impedance is calculated in accordance with JESD 51-7. electrical characteristics, VCC± = ±15 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA† MIN TYP MAX UNIT VIO Input offset voltage VO =0 RS =50 Ω 25 °C 3 15 mV VIO Input offset voltage VO = 0, RS = 50 Ω Full range 20 mV a V IO Temperature coefficient of input offset voltage VO = 0, RS = 50 Ω Full range 18 µV/°C IIO Input offset current‡ VO =0 25 °C 5 200 pA IIO Input offset current‡ VO = 0 Full range 2 nA IIB Input bias current‡ VO =0 25 °C 30 400 pA IIB Input bias current‡ VO = 0 Full range 10 nA VICR Common-mode input voltage range 25 °C ±11 –12 to 15 V RL = 10 kΩ 25 °C ±12 ±13.5 VOM Maximum peak output voltage swing RL ≥ 10 kΩ Full range ±12 V RL ≥ 2 kΩ Full range ±10 ±12 AVD Large signal differential voltage amplification VO = ±10 V RL ≥ 2kΩ 25 °C 25 200 V/mV AVD Large-signal differential voltage amplification VO = ±10 V, RL ≥ 2 kΩ Full range 15 V/mV B1 Unity-gain bandwidth 25 °C 3 MHz ri Input resistance 25 °C 1012 Ω CMRR Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω 25 °C 70 86 dB kSVR Supply-voltage rejection ratio ( ∆VCC±/∆VIO) VCC = ±15 V to ±9 V, VO = 0, RS = 50 Ω 25 °C 70 86 dB ICC Supply current VO = 0, No load 25 °C 1.4 2.8 mA VO1/VO2 Crosstalk attenuation AVD = 100 25 °C 120 dB † All characteristics are measured under open-loop conditions with zero common-mode voltage unless otherwise specified. Full range for TA is –40 °C to 85°C. ‡ Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive, as shown in Figure 5. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. |
Аналогичный номер детали - TL080 |
|
Аналогичное описание - TL080 |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |