поискавой системы для электроныых деталей |
|
TEA6322 датащи(PDF) 6 Page - NXP Semiconductors |
|
TEA6322 датащи(HTML) 6 Page - NXP Semiconductors |
6 / 36 page 1995 Dec 19 6 Philips Semiconductors Preliminary specification Sound fader control circuit TEA6322T The last section of the circuit is the volume II block. The balance and fader functions are performed using the same control blocks. This is realized by 4 independently controllable attenuators, one for each output. The control range of these attenuators is 55 dB in steps of 1 dB with an additional mute step. The circuit provides 3 mute modes: 1. Zero crossing mode mute via I2C-bus using 2 independent zero crossing detectors (ZCM, see Tables 2 and 9). 2. Fast mute via MUTE pin. 3. Fast mute via I2C-bus either by general mute (GMU, see Tables 2 and 9) or volume II block setting (see Table 4). The mute function is performed immediately if ZCM is cleared (ZCM = 0). If the bit is set (ZCM = 1) the mute is activated after changing the GMU bit. The actual mute switching is delayed until the next zero crossing of the audio frequency signal. As the two audio channels (left and right) are independent, two comparators are built-in to control independent mute switches. To avoid a large delay of mute switching when very low frequencies are processed or the output signal amplitude is lower than the DC offset voltage a second I2C-bus transmission is needed. Both transmissions have the same data and the second transmission a delay time of e.g. 100 ms. The first transmission starts the zero cross circuit, but second transmission moves the mute switch immediately if the circuit has no zero cross detected. The mute function can also be controlled externally. If the mute pin is switched to ground all outputs are muted immediately (except the outputs volume left and right (OVL and OVR) and hardware mute). This mute request overwrites all mute controls via the I2C-bus for the time the pin is held LOW. The hardware mute position is not stored in the TEA6322T. The MUTE pin can also be used as output. The mute pin voltage is LOW when all outputs are in mute position. For the turn on/off behaviour the following explanation is generally valid. To avoid AF output caused by the input signal coming from preceding stages, which produces output during drop of VCC, the mute has to be set, before the VCC will drop. This can be achieved by I2C-bus control or by grounding the MUTE pin. For use where is no mute in the application before turn off, a supply voltage drop of more than 1 × VBE will result in a mute during the voltage drop. The power supply should include a VCC buffer capacitor, which provides a discharging time constant. If the input signal does not disappear after turn off the input will become audible after certain time. A 4.7 k Ω resistor discharges the VCC buffer capacitor, because the internal current of the IC does not discharge it completely. The hardware mute function is favourable for use in Radio Data System (RDS) applications. The zero crossing mute avoids modulation plops. This feature is an advantage for mute during changing presets and/or sources (e.g. traffic announcement during cassette playback). LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). Note 1. Human body model: C = 100 pF; R = 1.5 k Ω; V ≥ 2 kV. Charge device model: C = 200 pF; R = 0 Ω; V ≥ 500 V. SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCC supply voltage 0 10 V Vn voltage at pins 1, 2 and 5 to 40 to pins 3 and 4 0VCC V Tamb operating ambient temperature −40 +85 °C Tstg storage temperature −65 +150 °C Ves electrostatic handling note 1 |
Аналогичный номер детали - TEA6322 |
|
Аналогичное описание - TEA6322 |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |