поискавой системы для электроныых деталей |
|
TDA7295S датащи(PDF) 8 Page - STMicroelectronics |
|
TDA7295S датащи(HTML) 8 Page - STMicroelectronics |
8 / 13 page The TDA7295S is a monolithic MOS power ampli- fier which can be operated at 76V supply voltage (80V with no signal applied) while delivering out- put currents up to ±6A. This allows the use of this device as a very high power amplifier (up to 80W as peak power with T.H.D.=10 % and Rl = 4 Ohm); the only drawback is the power dissipation, hardly manageable in the above power range. The typical junction-to-case thermal resistance of the TDA7295S is 1 oC/W (max= 1.5 oC/W). To avoid that, in worst case conditions, the chip tem- perature exceedes 150 oC, the thermal resistance of the heatsink must be 0.038 oC/W (@ max am- bient temperature of 50 oC). As the above value is pratically unreachable; a high efficiency system is needed in those cases where the continuous RMS output power is higher than 50-60 W. The TDA7295S was designed to work also in higher efficiency way. For this reason there are four power supply pins: two intended for the signal part and two for the power part. T1 and T2 are two power transistors that only operate when the output power reaches a certain threshold (e.g. 20 W). If the output power in- creases, these transistors are switched on during the portion of the signal where more output volt- age swing is needed, thus ”bootstrapping” the power supply pins (#13 and #15). The current generators formed by T4, T7, zener diodes Z1, Z2 and resistors R7,R8 define the minimum drop across the power MOS transistors of the TDA7295S. L1, L2, L3 and the snubbers C9, R1 and C10, R2 stabilize the loops formed by the ”bootstrap” circuits and the output stage of the TDA7295S. By considering again a maximum average output power (music signal) of 20W, in case of the high efficiency application, the thermal resistance value needed from the heatsink is 2.2 oC/W (Vs =±38V and Rl= 8 Ohm). All components (TDA7295S and po wer tran- sistors T1 and T2) can be placed on a 1.5 oC/W heatsink, with the power darlingtons electrically insulated from the heatsink. Since the total power dissipation is less than that of a usual class AB amplifier, additional cost sav- ings can be obtained while optimizing the power supply, even with a high heatsink . BRIDGE APPLICATION Another application suggestion is the BRIDGE configuration, where two TDA7295S are used. In this application, the value of the load must not be lower than 8 Ohm for dissipation and current capability reasons. A suitable field of application includes HI-FI/TV subwoofers realizations. The main advantages offered by this solution are: - High power performances with limited supply voltage level. - Considerably high output power even with high load values (i.e. 16 Ohm). With Rl = 8 Ohm, VS = ±25V the maximum output power obtainable is 150W (Music Power) APPLICATION NOTE: (ref. fig. 7) Modular Application (more Devices in Parallel) The use of the modular application lets very high power be delivered to very low impedance loads. The modular application implies one device to act as a master and the others as slaves. The slave power stages are driven by the master device and work in parallel all together, while the input and the gain stages of the slave device are disabled, the figure below shows the connections required to configure two devices to work to- gether. The master chip connections are the same as the normal single ones. The outputs can be connected together with- out the need of any ballast resistance. The slave SGND pin must be tied to the nega- tive supply. The slave ST-BY pin must be connected to ST-BY pin. The bootstrap lines must be connected to- gether and the bootstrap capacitor must be in- creased: for N devices the boostrap capacitor must be 22 µF times N. The slave Mute and IN-pins must be grounded. THE BOOTSTRAP CAPACITOR For compatibility purpose with the previous de- vices of the family, the boostrap capacitor can be connected both between the bootstrap pin (6) and the output pin (14) or between the boostrap pin (6) and the bootstrap loader pin (12). TDA7295S 8/13 |
Аналогичный номер детали - TDA7295S |
|
Аналогичное описание - TDA7295S |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |