поискавой системы для электроныых деталей |
|
LA4814V датащи(PDF) 6 Page - Sanyo Semicon Device |
|
LA4814V датащи(HTML) 6 Page - Sanyo Semicon Device |
6 / 17 page LA4814V No.A0972-6/17 5.Second amplifier control function (only when BTL mode is used) The second amplifier control function is a function to reduce the startup pop-noise in BTL mode. The pop noise can be reduced by first turning on the IC while the second amplifier is stopped, then after the potential inside the IC gets stabilized, turning on the second amplifier. The values shown below are recommended for the control time. C5 [ μF] 2.2 3.3 4.7 10 Twu [ms] 200 250 300 500 * Twu : Time after releasing standby to second amplifier turn-on a) When using microcomputer control The second amplifier can be controlled by applying the following voltages to pin 9. Second amplifier operation mode … V9 ≤ 0.3V Second amplifier stop mode … V9 ≥ 1.6V However, set the resistance value of the resistor R6 inserted in series in such a way that the condition in the following formula is met. R6 ≤ 16.2 × (Vcnt - 1.6) kΩ The pin 9 injected current is expressed by the following formula : I9 = (57.6 × Vcnt - 31.7)/(1+0.058 × R6) μA Fig. 3 b) When microcomputer control is not possible When the microcomputer cannot be used, the second amplifier can be controlled by adding the external components as shown in Fig. 4. VCC (V) 5 3.6 3 R7 (k Ω) 10 6.8 6.8 R9 (k Ω) 120 68 56 C8 ( μF) 100 100 100 Fig. 4 6.Shorting between pins When power is applied with pins left short-circuited, electrical deterioration or damage may result. Therefore, check before power application if pins are short-circuited with solder, etc. during mounting of IC. 7.Load shorting If the load is left short-circuited for a long period of time, electrical deterioration or damage may occur. Never allow the load to short-circuit. 8.Maximum rating When IC is used near the maximum rating, there is a possibility that the maximum rating may be exceeded even under the smallest change of conditions, resulting in failure. Take sufficient margin for variation of supply voltage and use IC within a range where the maximum rating will never be exceeded. Vcnt CNT R6 V9 9 + R7 C8 R5 R9 VCC VCC CNT STBY 14 9 8 |
Аналогичный номер детали - LA4814V |
|
Аналогичное описание - LA4814V |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |