поискавой системы для электроныых деталей |
|
VRE4112C датащи(PDF) 7 Page - Cirrus Logic |
|
VRE4112C датащи(HTML) 7 Page - Cirrus Logic |
7 / 8 page P r o d u c t I n n o v a t i o n F r o m VRE4100 VRE4100DS REVERSEcuRREntpAth The P-channel pass transistor used in this series has an inherent diode connected between the Vin and VOUT pins. Forcing the output to voltages higher than the input or pulling Vin below the voltage stored in the output capacitor by more than the Vbe will forward bias this diode and current will flow from the Vout pin to Vin. This will not damage the device as long as the current does not exceed 50 mA. on/oFFopERAtion This series features a sleep mode that is activated by pulling the enable pin low. To turn the reference on, the en- able pin is pulled high. If this feature is not used, the enable pin should be tied to Vin to keep the reference on at all times. The enable pin must not be left unconnected (floating). When powered off, these devices will quickly reduce both Vout and IQ to zero. During power down, the charge across the output capacitor is discharged to ground through the internal circuitry. On power up, the Vout is restored in less than 200 μs. The signal source used to drive the enable pin can come from either a totem-pole output or an open collector output with a pull-up resistor to the input voltage. The signal source must be able to swing above and below the voltage thresholds to guarantee an ON or OFF state. It must not exceed the absolute maximum rating for the enable pin. outputAccuRAcY The output accuracy after assembly at room temperature is made up of three components: initial accuracy of the de- vice, thermal hysteresis, and mechanical stress. The initial accuracy is measured at the factory and may not reflect the actual output voltage when the devices are mounted to a PCB. The effects of mechanical stress and thermal hysteresis can shift the output voltage. thERMAlhYStERESiS Thermal hysteresis is a change in output voltage as a result of a temperature change. When references experience a temperature change and return to the initial temperature, they do not always have the same initial voltage. Ther- mal hysteresis is difficult to correct and is a major error source in systems that experience temperature changes greater than 25°C. Reference vendors are starting to include this important specification in their datasheets MEchAnicAlhYStERESiS Recommendations to minimize mechanical stress: 1) Mount the VRE4112/VRE4125/VRE4141 near the edges or corners of the PCB. The center of the board generally has the highest mechanical and thermal stress. 2) Mechanically isolate the device by cutting a U shaped slot around the package. This provides some mechanical and thermal isolation from the rest of the circuit. pinconFiGuRAtion 5 6 7 8 VRE4100 TOP VIEW 1 2 3 4 NC +VIN Enable GND NC VREF NC NC |
Аналогичный номер детали - VRE4112C |
|
Аналогичное описание - VRE4112C |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |