поискавой системы для электроныых деталей |
|
ISL45042IR-T датащи(PDF) 4 Page - Intersil Corporation |
|
ISL45042IR-T датащи(HTML) 4 Page - Intersil Corporation |
4 / 8 page 4 FN6072.8 July 9, 2008 Application Information The application circuit to adjust the VCOM voltage in an LCD panel is shown in Figure 1. The ISL45042 has a 128-step sink current resolution. The output is connected to an external voltage divider that results in decreasing the output VCOM voltage as you increase the ISL45042 sink current. CTL Pin The adjustment of the output VCOM voltage and the programming of the non-volatile memory are provided through a single pin called CTL when the CE pin is high. The output VCOM voltage is increased with a mid (VDD/2) to high transition (0.8*VDD) on the CTL pin. The output VCOM voltage is decreased with a mid (VDD/2) to low transition (0.3*VDD) on the CTL pin (see Figure 7). Once the minimum or maximum value is reached on the 128 steps, the device will not overflow or underflow beyond that minimum or maximum value. Programming of the non-volatile memory occurs when the CTL pin exceeds 4.9V. The CTL signal needs to remain above 4.9V for more than 200µs. The level and timing CTL EEPROM Programming Signal Time CTLPT >4.9V Full 200 - - µs Programming Time PT Full - - 100 ms SET Voltage Resolution SETVR (Note 5) Full 7 7 7 Bits SET Differential Nonlinearity SETDN Monotonic Over-Temperature Full - - ±1 LSB SET Zero-Scale Error SETZSE Full - - ±2 LSB SET Full-Scale Error SETFSE Full - - ±8 LSB SET Current ISET Through RSET (Note 8) Full - 20 - µA SET External Resistance SETER To GND, AVDD = 20V Full 10 - 200 k Ω To GND, AVDD = 4.5V Full 2.25 - 45 k Ω AVDD to SET Voltage Attenuation AVDD to SET Full - 1:20 - V/V OUT Settling Time OUTST To ±0.5 LSB Error Band (Note 6) Full - 20 - µs OUT Voltage Range VOUT Full VSET + 0.5V - 13 V OUT Voltage Drift OUTVD (Note 6) 25 to 55 - <10 - mV NOTES: 3. CTL signal only needs to be greater than 4.9V to program EEPROM. 4. Tested at AVDD = 20V. 5. The Counter value is set to mid-scale ±4 LSB’s in the Production. 6. Simulated and Determined via Design and NOT Directly Tested. 7. Simulated Maximum Current Draw when Programming EEPROM is 23mA; should be considered when designing Power Supply. 8. A Typical Current of 20µA is Calculated using the AVDD = 10V and RSET = 24.9kΩ. Reference “RSET Resistor” on page 6. 9. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. Electrical Specifications Test Conditions: VDD = 3V, AVDD = 10V, OUT = 5V, RSET = 24.9kΩ; Unless Otherwise Specified. Typicals are at TA = +25°C (Continued) PARAMETER SYMBOL TEST CONDITIONS TEMP (°C) MIN (Note 9) TYP MAX (Note 9) UNITS RSET FIGURE 1. VCOM ADJUSTMENT IN AN LCD PANEL ISL45042 SET OUT AVDD R1 R2 AVDD ISINK VCOM SINGLE PIXEL CTL CE IN LCD PANEL + - COLUMN DRIVER ISL45042 |
Аналогичный номер детали - ISL45042IR-T |
|
Аналогичное описание - ISL45042IR-T |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |