поискавой системы для электроныых деталей |
|
ISL22424TFR16Z датащи(PDF) 7 Page - Intersil Corporation |
|
ISL22424TFR16Z датащи(HTML) 7 Page - Intersil Corporation |
7 / 18 page 7 FN6425.0 May 31, 2007 Cpin (Note 20) SCK, SDI, SDO and CS pin capacitance 10 pF fSCK SPI frequency 5MHz tCYC SPI clock cycle time 200 ns tWH SPI clock high time 100 ns tWL SPI clock low time 100 ns tLEAD Lead time 250 ns tLAG Lag time 250 ns tSU SDI, SCK and CS input setup time 50 ns tH SDI, SCK and CS input hold time 50 ns tRI SDI, SCK and CS input rise time 10 ns tFI SDI, SCK and CS input fall time 10 20 ns tDIS SDO output Disable time 0 100 ns tSO SDO output setup time 50 ns tV SDO output valid time 150 ns tHO SDO output hold time 0 ns tRO SDO output rise time Rpu = 2k, Cbus = 30pF 60 ns tFO SDO output fall time Rpu = 2k, Cbus = 30pF 60 ns tCS CS deselect time 2µs NOTES: 4. Typical values are for TA = +25°C and 3.3V supply voltage. 5. LSB: [V(RW)255 – V(RW)0]/255. V(RW)255 and V(RW)0 are V(RW) for the DCP register set to FF hex and 00 hex respectively. LSB is the incremental voltage when changing from one tap to an adjacent tap. 6. ZS error = V(RW)0/LSB. 7. FS error = [V(RW)255 – VCC]/LSB. 8. DNL = [V(RW)i – V(RW)i-1]/LSB-1, for i = 1 to 255. i is the DCP register setting. 9. INL = [V(RW)i – i • LSB – V(RW)]/LSB for i = 1 to 255. 10. VMATCH= [V(RWx)i -V(RWy)i]/LSB, for i = 0 to 255, x = 0 to 1, y = 0 to 1. 11. for i = 16 to 240 decimal, T = -40°C to +125°C. Max( ) is the maximum value of the wiper voltage and Min ( ) is the minimum value of the wiper voltage over the temperature range. 12. MI = |RW255 – RW0|/255. MI is a minimum increment. RW255 and RW0 are the measured resistances for the DCP register set to FF hex and 00 hex respectively. 13. Roffset = RW0/MI, when measuring between RW and RL. Roffset = RW255/MI, when measuring between RW and RH. 14. RDNL = (RWi – RWi-1)/MI -1, for i = 1 to 255. 15. RINL = [RWi – (MI • i) – RW0]/MI, for i = 1 to 255. 16. RMATCH= [(Rx)i -(Ry)i]/MI, for i = 0 to 255, x = 0 to 1, y = 0 to 1. 17. for i = 16 to 240, T = -40°C to +125°C. Max( ) is the maximum value of the resistance and Min ( ) is the minimum value of the resistance over the temperature range. 18. tWC is the time from the end of a Write sequence of SPI serial interface, to the end of the self-timed internal non-volatile write cycle. 19. Rpu is specified for the highest data rate transfer for the device. Higher value pull-up can be used at lower data rates. 20. This parameter is not 100% tested. Operating Specifications Over the recommended operating conditions unless otherwise specified. (Continued) SYMBOL PARAMETER TEST CONDITIONS MIN TYP (NOTE 4) MAX UNIT TC V Max V RW () i () Min V RW () i () – Max V RW () i () Min V RW () i () + [] 2 ⁄ ---------------------------------------------------------------------------------------------- 106 165°C ----------------- × = + TC R Max Ri () Min Ri () – [] Max Ri () Min Ri () + [] 2 ⁄ ---------------------------------------------------------------- 10 6 165°C ----------------- × = + ISL22424 |
Аналогичный номер детали - ISL22424TFR16Z |
|
Аналогичное описание - ISL22424TFR16Z |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |