поискавой системы для электроныых деталей |
|
AD13280AF датащи(PDF) 10 Page - Analog Devices |
|
AD13280AF датащи(HTML) 10 Page - Analog Devices |
10 / 20 page REV. 0 AD13280 –10– or AMP-IN-B-1 when an input of ±0.5 V full scale is desired. Use AMP-IN-A-2 or AMP-IN-B-2 when ±1 V full scale is desired. Each channel has an AMP-OUT which must be tied to either a noninverting or inverting input of a differential amplifier with the remaining input grounded. For example, Side A, AMP-OUT-A (Pin 6) must be tied to A+IN (Pin 5) with A–IN (Pin 5) tied to ground for noninverting operation or AMP-OUT-A (Pin 6) tied to A–IN (Pin 4) with A+IN (Pin 5) tied to ground for inverting operation. USING THE DIFFERENTIAL INPUT Each channel of the AD13280 was designed with two optional differential inputs, A+IN, A–IN and B+IN, B–IN. The inputs provide system designers with the ability to bypass the AD8037 amplifier and drive the AD8138 directly. The AD8138 differen- tial ADC driver can be deployed in either a single-ended or differential input configuration. The differential analog inputs have a nominal input impedance of 620 Ω and nominal full- scale input range of 1.2 V p-p. The AD8138 amplifier drives a differential filter and the custom analog-to-digital converter. The differential input configuration provides the lowest even-order harmonics and signal-to-noise (SNR) performance improvement of up to 3 dB (SNR = 73 dBFS). Exceptional care was taken in the layout of the differential input signal paths. The differential input transmission line characteristics are matched and balanced. Equal attention to system level signal paths must be provided in order to realize significant performance improvements. APPLYING THE AD13280 Encoding the AD13280 The AD13280 encode signal must be a high quality, extremely low phase noise source, to prevent degradation of performance. Maintaining 12-bit accuracy at 80 MSPS places a premium on encode clock phase noise. SNR performance can easily degrade 3 dB to 4 dB with 37 MHz input signals when using a high-jitter clock source. See Analog Devices’ Application Note AN-501, “Aperture Uncertainty and ADC System Performance” for complete details. For optimum performance, the AD13280 must be clocked differentially. The encode signal is usually ac-coupled into the ENCODE and ENCODE pins via a transformer or capacitors. These pins are biased internally and require no addi- tional bias. Shown below is one preferred method for clocking the AD13280. The clock source (low jitter) is converted from single-ended to differential using an RF transformer. The back-to-back Schottky diodes across the transformer secondary limit clock excursions into the AD13280 to approximately 0.8 V p-p differential. This helps prevent the large voltage swings of the clock from feeding through to the other portions of the AD13280, and limits the noise presented to the ENCODE inputs. A crystal clock oscillator can also be used to drive the RF transformer if an appropriate limited resistor (typically 100 Ω) is placed in the series with the primary. T1-4T 100 0.1 F ENCODE ENCODE AD13280 HSMS2812 DIODES CLOCK SOURCE Figure 6. Crystal Clock Oscillator—Differential Encode If a low jitter ECL/PECL clock is available, another option is to ac-couple a differential ECL/PECL signal to the encode input pins as shown below. A device that offers excellent jitter perfor- mance is the MC100LVEL16 (or same family) from Motorola. ENCODE ENCODE AD13280 0.1 F ECL/ PECL VT VT 0.1 F Figure 7. Differential ECL for Encode Jitter Consideration The signal-to-noise ratio (SNR) for any ADC can be predicted. When normalized to ADC codes, Equation 1 accurately predicts the SNR based on three terms. These are jitter, average DNL error, and thermal noise. Each of these terms contributes to the noise within the converter. SNR f t V N ANALOG RMS NOISE RMS N =× + () +× × × + – log ( ) / 20 1 2 2 2 2 2 12 ε π J (1) fANALOG = analog input frequency tJ RMS = rms jitter of the encode (rms sum of encode source and internal encode circuitry) ε = average DNL of the ADC (typically 0.50 LSB) N = Number of bits in the ADC VNOISE RMS = V rms noise referred to the analog input of the ADC (typically 5 LSB) For a 12-bit analog-to-digital converter like the AD13280, aper- ture jitter can greatly affect the SNR performance as the analog frequency is increased. The chart below shows a family of curves that demonstrates the expected SNR performance of the AD13280 as jitter increases. The chart is derived from the above equation. For a complete discussion of aperture jitter, please consult Ana- log Devices’ Application Note AN-501, “Aperture Uncertainty and ADC System Performance.” CLOCK JITTER – ps 60 AIN = 5MHz AIN = 10MHz AIN = 20MHz AIN = 37MHz 61 62 63 64 65 66 67 68 69 70 71 59 58 Figure 8. SNR vs. Jitter |
Аналогичный номер детали - AD13280AF |
|
Аналогичное описание - AD13280AF |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |