поискавой системы для электроныых деталей
  Russian  ▼
ALLDATASHEETRU.COM

X  

AD8322ARU-REEL датащи(PDF) 10 Page - Analog Devices

номер детали AD8322ARU-REEL
подробное описание детали  5 V CATV Line Driver Coarse Step Output Power Control
Download  16 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
производитель  AD [Analog Devices]
домашняя страница  http://www.analog.com
Logo AD - Analog Devices

AD8322ARU-REEL датащи(HTML) 10 Page - Analog Devices

Back Button AD8322ARU-REEL Datasheet HTML 6Page - Analog Devices AD8322ARU-REEL Datasheet HTML 7Page - Analog Devices AD8322ARU-REEL Datasheet HTML 8Page - Analog Devices AD8322ARU-REEL Datasheet HTML 9Page - Analog Devices AD8322ARU-REEL Datasheet HTML 10Page - Analog Devices AD8322ARU-REEL Datasheet HTML 11Page - Analog Devices AD8322ARU-REEL Datasheet HTML 12Page - Analog Devices AD8322ARU-REEL Datasheet HTML 13Page - Analog Devices AD8322ARU-REEL Datasheet HTML 14Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 10 / 16 page
background image
REV. 0
AD8322
–10–
Single-Ended-to-Differential Input (Figure 8 Option 1)
Install the Mini-Circuits T1-6T-KK81 1:1 transformer in the T1
location of the evaluation board. Install 0
Ω chip resistors in R12,
R13, and R17, and leave R14, R16, and R19 open. For 75
input impedance, install a 110
Ω resistor in R7 located on the back
side of the evaluation board and leave R5 and R6 open. In this
configuration the input signal must be applied to the VIN+ port of
the evaluation board from a single-ended 75
Ω signal source. For
input impedances other than 75
Ω, use the following equation
to compute the correct value for R7.
Desired Input Impedance = R7 235
Single-Ended-to-Differential Input (Figure 8 Option 2)
Install the Mini-Circuits T1-6T-KK81 1:1 transformer in the T1
location of the evaluation board. Install 0
Ω chip resistors in R12,
R13, R17, and R19, and leave R14 and R16 open. For 75
Ω input
impedance, install 55
Ω resistors in R5 and R6 located on the back
side of the evaluation board and leave R7 open. In this configu-
ration the input signal must be applied to the VIN+ port of the
evaluation board from a single-ended 75
Ω signal source. For
input impedances other than 75
Ω, use the following equation
to compute the correct values for R5 and R6.
R5 = R6 = R, Desired Input Impedance = 2
× (R 117.5)
Differential Input (Figure 8 Option 3)
If a differential signal source is available, it may be applied directly
to both the VIN+ and VIN– input ports of the evaluation board. In
this case, install 0
Ω chip resistors in R8, R14, R15, and R16, and
leave R12, R13, and R19 open. Referring to Figure 8 Option 3 and
the AD8322 evaluation board, a differential input impedance
of 150
Ω can be achieved by installing a 432 Ω resistor in R7,
leaving R5 and R6 open. If another input impedance is desired,
the following equation can be used to compute the correct
value for R7.
Desired Input Impedance = R7 235
DIFF IN
T1
AD8322
R7
OPTION 1 DIFFERENTIAL INPUT TERMINATION
DIFF IN
T1
R5
R6
AD8322
OPTION 2 DIFFERENTIAL INPUT TERMINATION
R7
VIN+
AD8322
VIN–
OPTION 3 DIFFERENTIAL INPUT TERMINATION
Figure 8. Differential Input Termination Options
Installing the Visual Basic Control Software
To install the “CABDRIVE_22” evaluation board control soft-
ware, first close all Windows applications and run “SETUP.EXE”
located on Disk 1 of the AD8322 Evaluation Software. Follow
the on-screen instructions and insert Disk 2 when prompted to
do so. Enter the path of the directory into which the software
will be installed and select the button in the upper left corner to
complete the installation.
Running the Software
To invoke the control software, go to START -> PROGRAMS
-> CABDRIVE_22, or select the AD8322.EXE icon from the
directory containing the software.
Controlling the Gain/Attenuation of the AD8322
The slide bar controls the AD8322’s gain/attenuation, which is
displayed in dB and in V/V. Although the AD8322 is designed
for use at the eight gain codes described in the SPI Programming
and Gain Adjustment section, all of the intermediate codes are
included in the software. Code 0 is also included because of the
high isolation it provides. The gain code (i.e., position of the slide
bar) is displayed in decimal, binary, and hexadecimal (see
Figure 9).
POWER-UP AND POWER-DOWN
The “Power-Up” and “Power-Down” buttons select the mode of
operation of the AD8322 by controlling the logic level on the
asynchronous
PD pin. The “Power-Up” button applies a Logic
1 to the
PD pin putting the AD8322 in forward transmit mode.
The “Power-Down” button applies a Logic 0 to the
PD pin select-
ing reverse mode, where the forward signal transmission is disabled
while a back termination of 75
Ω is maintained.
Memory Section
The “MEMORY” section of the software provides a convenient
way to alternate between two gain settings. The “X->M1” but-
ton stores the current value of the gain slide bar into memory
while the “RM1” button recalls the stored value, returning the
gain slide bar to that level. The “X->M2” and “RM2” buttons
work in the same manner.


Аналогичный номер детали - AD8322ARU-REEL

производительномер деталидатащиподробное описание детали
logo
Analog Devices
AD8322 AD-AD8322_15 Datasheet
687Kb / 16P
   5 V CATV Line Driver Coarse Step Output Power Control
REV. 0
More results

Аналогичное описание - AD8322ARU-REEL

производительномер деталидатащиподробное описание детали
logo
Analog Devices
AD8322 AD-AD8322_15 Datasheet
687Kb / 16P
   5 V CATV Line Driver Coarse Step Output Power Control
REV. 0
AD8327 AD-AD8327 Datasheet
307Kb / 20P
   5 V CATV Line Driver Coarse Step Output Power Control
REV. 0
AD8327 AD-AD8327_15 Datasheet
885Kb / 20P
   5 V CATV Line Driver Coarse Step Output Power Control
REV. 0
AD8323 AD-AD8323 Datasheet
277Kb / 16P
   5 V CATV Line Driver Fine Step Output Power Control
REV. 0
AD8325 AD-AD8325 Datasheet
304Kb / 16P
   5 V CATV Line Driver Fine Step Output Power Control
REV. 0
AD8325 AD-AD8325_05 Datasheet
736Kb / 16P
   5 V CATV Line Driver Fine Step Output Power Control
REV. A
AD8323 AD-AD8323_15 Datasheet
715Kb / 16P
   5 V CATV Line Driver Fine Step Output Power Control
REV. 0
AD8326 AD-AD8326 Datasheet
475Kb / 24P
   High Output Power Programmable CATV Line Driver
REV. 0
AD8326 AD-AD8326_15 Datasheet
1Mb / 24P
   High Output Power Programmable CATV Line Driver
REV. 0
AD8321ARZ AD-AD8321ARZ Datasheet
593Kb / 20P
   Gain Programmable CATV Line DRiver
REV. A
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16


датащи скачать

Go To PDF Page


ссылки URL




Конфиденциальность
ALLDATASHEETRU.COM
Вашему бизинису помогли Аллдатащит?  [ DONATE ] 

Что такое Аллдатащит   |   реклама   |   контакт   |   Конфиденциальность   |   обмен ссыками   |   поиск по производителю
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com