поискавой системы для электроныых деталей |
|
AZT71_1301 датащи(PDF) 6 Page - Arizona Microtek, Inc |
|
AZT71_1301 датащи(HTML) 6 Page - Arizona Microtek, Inc |
6 / 14 page Arizona Microtek, Inc. AZT71 Programmable Capacitive Tuning IC www.azmicrotek.com +1-480-962-5881 6 Request a Sample Jan 2013, Rev 1.3 PROGRAMMING TO THE SHIFT REGISTER Control word bits are inputted serially through the DA pin timed with the rising edge of the CLK pin. Figure 7 shows the control word 11001100100 has been serially entered into the register. Note that bit0 is the 1 st bit to enter and bit10 is the last. In the AZT71, bit0 does not affect the capacitance value but still must be included in the serial bit stream. For the shift register, capacitors are selected when bits are active HIGH. For the AZT71 to read from the shift register, the CLK pin must remain HIGH. t DA CLK bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 bit 8 bit 9 bit 10 Register data active when CLK is high bit 0 loaded 1st Figure 7 - Shift register programming WRITING DATA TO THE EEPROM Once the desired capacitance value has been determined, the digital control word can be written or re-written into the EEPROM. By storing the control word in the EEPROM, the customer is prevented from making adjustments from the factory set programming data. This is accomplished within the AZT71 with internal pull-downs on the DA, PV, and CLK pins. The detailed sequence for writing data to the EEPROM within the AZT71 is described in Table 6. Note that with EEPROM, capacitors are selected when bits are active LOW. Table 6 – Data writing sequence for EEPROM Step Action 1 Determine the desired capacitor control word with the operational power supply voltage and desired oscillator conditions 2 Set the VDD supply voltage to +5.0V 3 If EEPROM is not already erased, erase EEPROM (see ERASING THE EEPROM) 4 Read the current state of the EEPROM bits (see READING BACK FROM THE EEPROM) 5 Compare the desired control word to the stored EEPROM control word. Count the number of differences so as to prevent double/redundant writing 6 One bit at a time, load the first desired control word bit (bit selection for EEPROM is active LOW) 7 Set the PV pin to +6V (≥5.6V, ≤6.1V) with the pulse and idle shown in timing diagram (Figure 10) 8 Progress through all necessary control word bits by repeating steps 5 & 6 until all bits are set to the desired control word. 9 Verify the correct EEPROM contents by reading back the individual bits |
Аналогичный номер детали - AZT71_1301 |
|
Аналогичное описание - AZT71_1301 |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |