поискавой системы для электроныых деталей |
|
AD7817BRZ датащи(PDF) 8 Page - Analog Devices |
|
AD7817BRZ датащи(HTML) 8 Page - Analog Devices |
8 / 20 page AD7817/AD7818 Data Sheet Rev. D | Page 8 of 20 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS 1 2 3 4 5 6 7 8 BUSY OTI CS VIN1 REFIN AGND CONVST VIN2 16 15 14 13 12 11 10 9 SCLK DIN DOUT VIN4 VIN3 VDD DGND RD/WR AD7817 TOP VIEW (Not to Scale) Figure 4. AD7817 Pin Configuration Table 4. AD7817 Pin Function Descriptions Pin No. Mnemonic Description 1 CONVST Logic Input Signal. The convert start signal. A 10-bit analog-to-digital conversion is initiated on the falling edge of this signal. The falling edge of this signal places track-and-hold in hold mode. Track-and-hold goes into track mode again at the end of the conversion. The state of the CONVST signal is checked at the end of a conversion. If it is logic low, the AD7817 powers down. See the Operating Modes section. 2 BUSY Logic Output. The busy signal is logic high during a temperature or voltage A/D conversion. The signal can be used to interrupt a microcontroller when a conversion has finished. 3 OTI Logic Output. The overtemperature indicator (OTI) is set logic low if the result of a conversion on Channel 0 (temperature sensor) is greater that an 8-bit word in the overtemperature register (OTR). The signal is reset at the end of a serial read operation, that is, a rising RD/WR edge when CS is low. 4 CS Logic Input Signal. The chip select signal is used to enable the serial port of the AD7817. This is necessary if the AD7817 is sharing the serial bus with more than one device. 5 AGND Analog Ground. Ground reference for track-and-hold comparator and capacitor DAC. 6 REF IN Analog Input. An external 2.5 V reference can be connected to the AD7817 at this pin. To enable the on-chip reference, tie the REF IN pin to AGND. If an external reference is connected to the AD7817, the internal reference shuts down. 7 to 10 V IN1 to VIN4 Analog Input Channels. The AD7817 has four analog input channels. The input channels are single-ended with respect to AGND (analog ground). The input channels can convert voltage signals in the range 0 V to V REF. A channel is selected by writing to the address register of the AD7817. See the Control Byte section. 11 V DD Positive Supply Voltage, 2.7 V to 5.5 V. 12 DGND Digital Ground. Ground reference for digital circuitry. 13 D OUT Logic Output with a High Impedance State. Data is clocked out of the AD7817 serial port at this pin. This output goes into a high impedance state on the falling edge of RD/WR or on the rising edge of the CS signal, whichever occurs first. 14 D IN Logic Input. Data is clocked into the AD7817 at this pin. 15 SCLK Clock Input for the Serial Port. The serial clock is used to clock data into and out of the AD7817. Data is clocked out on the falling edge and clocked in on the rising edge. 16 RD/WR Logic Input Signal. The read/write signal is used to indicate to the AD7817 whether the data transfer operation is a read or a write. Set the RD/WR logic high for a read operation and logic low for a write operation. |
Аналогичный номер детали - AD7817BRZ |
|
Аналогичное описание - AD7817BRZ |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |