ADC104S021CIMMX datasheet(7/19 Pages) NSC

номер детали	ADC104S021CIMMX

подробное описание детали	4 Channel, 200 kSPS, 10-Bit A/D Converter

Download	19 Pages

Scroll/Zoom	100%

производитель	NSC [National Semiconductor (TI)]

домашняя страница	http://www.national.com

Logo

7 / 19 page

Specification Definitions

ACQUISITION TIME is the time required to acquire the input

voltage. That is, it is time required for the hold capacitor to

charge up to the input voltage.

APERTURE DELAY is the time between the fourth falling

SCLK edge of a conversion and the time when the input

signal is acquired or held for conversion.

CONVERSION TIME is the time required, after the input

voltage is acquired, for the ADC to convert the input voltage

to a digital word.

CROSSTALK is the coupling of energy from one channel

into the other channel, or the amount of signal energy from

one analog input that appears at the measured analog input.

DIFFERENTIAL NON-LINEARITY (DNL) is the measure of

the maximum deviation from the ideal step size of 1 LSB.

DUTY CYCLE is the ratio of the time that a repetitive digital

waveform is high to the total time of one period. The speci-

fication here refers to the SCLK.

EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE

BITS) is another method of specifying Signal-to-Noise and

Distortion

or

SINAD.

ENOB

is

defined

as

(SINAD − 1.76) / 6.02 and says that the converter is equiva-

lent to a perfect ADC of this (ENOB) number of bits.

FULL POWER BANDWIDTH is a measure of the frequency

at which the reconstructed output fundamental drops 3 dB

below its low frequency value for a full scale input.

GAIN ERROR is the deviation of the last code transition

(111...110) to (111...111) from the ideal (V

REF − 1.5 LSB),

after adjusting for offset error.

INTEGRAL NON-LINEARITY (INL) is a measure of the

deviation of each individual code from a line drawn from

negative full scale (1⁄2 LSB below the first code transition)

through positive full scale (1⁄2 LSB above the last code

transition). The deviation of any given code from this straight

line is measured from the center of that code value.

INTERMODULATION DISTORTION (IMD) is the creation of

additional spectral components as a result of two sinusoidal

frequencies being applied to the ADC input at the same time.

It is defined as the ratio of the power in the second and third

order intermodulation products to the sum of the power in

both of the original frequencies. IMD is usually expressed in

dB.

MISSING CODES are those output codes that will never

appear at the ADC outputs. The ADC104S021 is guaranteed

not to have any missing codes.

OFFSET ERROR is the deviation of the first code transition

(000...000) to (000...001) from the ideal (i.e. GND + 0.5

LSB).

SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in

dB, of the rms value of the input signal to the rms value of the

sum of all other spectral components below one-half the

sampling frequency, not including harmonics or d.c.

SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD)

Is the ratio, expressed in dB, of the rms value of the input

signal to the rms value of all of the other spectral compo-

nents below half the clock frequency, including harmonics

but excluding d.c.

SPURIOUS FREE DYNAMIC RANGE (SFDR) is the differ-

ence, expressed in dB, between the rms values of the input

signal and the peak spurious signal where a spurious signal

is any signal present in the output spectrum that is not

present at the input, excluding d.c.

TOTAL HARMONIC DISTORTION (THD) is the ratio, ex-

pressed in dB or dBc, of the rms total of the first five

harmonic components at the output to the rms level of the

input signal frequency as seen at the output. THD is calcu-

lated as

where A

f1 is the RMS power of the input frequency at the

output and A

f2 through Af6 are the RMS power in the first 5

harmonic frequencies.

THROUGHPUT TIME is the minimum time required between

the start of two successive conversion. It is the acquisition

time plus the conversion time. In the case of the

ADC104S021, this is 16 SCLK periods.

www.national.com

7

Аналогичный номер детали - ADC104S021CIMMX

производитель	номер детали	датащи	подробное описание детали
Texas Instruments	ADC104S021CIMMX/NOPB	1Mb / 27P	[Old version datasheet] 4-Channel, 50 ksps to 200 ksps, 10-Bit A/D Converter

More results

Аналогичное описание - ADC104S021CIMMX

производитель	номер детали	датащи	подробное описание детали
Texas Instruments	ADC104S021	1Mb / 27P	[Old version datasheet] 4-Channel, 50 ksps to 200 ksps, 10-Bit A/D Converter
Texas Instruments	ADC104S051CIMM	1Mb / 25P	[Old version datasheet] ADC104S051 4 Channel, 200 ksps to 500 ksps, 10-Bit A/D Converter
National Semiconductor ...	ADC124S021	909Kb / 19P	4 Channel, 200 kSPS, 12-Bit A/D Converter
	ADC108S022	842Kb / 17P	8-Channel, 50 kSPS to 200 kSPS, 10-Bit A/D Converter
	ADC108S052	839Kb / 17P	8-Channel, 200 kSPS to 500 kSPS, 10-Bit A/D Converter
Texas Instruments	ADC108S022	1Mb / 25P	[Old version datasheet] 8-Channel, 50 ksps to 200 ksps, 10-Bit A/D Converter
	ADC108S052	1Mb / 27P	[Old version datasheet] 8-Channel, 200 ksps to 500 ksps, 10-Bit A/D Converter
	ADC102S051	1Mb / 29P	[Old version datasheet] 2 Channel, 200 ksps to 500 ksps, 10-Bit A/D Converter
	ADC124S021	1Mb / 27P	[Old version datasheet] 4-Channel, 50 ksps to 200 ksps, 12-Bit A/D Converter
	ADC102S051	1Mb / 28P	[Old version datasheet] ADC102S051 2 Channel, 200 ksps to 500 ksps, 10-Bit A/D Converter

More results

ADC104S021CIMMX датащи(PDF) 7 Page - National Semiconductor (TI)

ADC104S021CIMMX датащи(HTML) 7 Page - National Semiconductor (TI)

Аналогичный номер детали - ADC104S021CIMMX

Аналогичное описание - ADC104S021CIMMX

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

датащи скачать

ссылки URL