поискавой системы для электроныых деталей |
|
TL497AIJ датащи(PDF) 1 Page - Texas Instruments |
|
TL497AIJ датащи(HTML) 1 Page - Texas Instruments |
1 / 20 page TL497A 500mA PEAK STEPUP, STEPDOWN, INVERTING SWITCHING VOLTAGE REGULATOR SLVS009F − JUNE 1976 − REVISED FEBRUARY 2005 1 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 D High Efficiency... 60% or Greater D Peak Switch Current . . . 500 mA D Input Current Limit Protection D TTL-Compatible Inhibit D Adjustable Output Voltage D Input Regulation . . . 0.2% Typ D Output Regulation . . . 0.4% Typ D Soft Start-Up Capability D Can be Used in Buck, Boost, and Inverting Configurations description/ordering information The TL497A incorporates all the active functions required in the construction of switching voltage regulators. It also can be used as the control element to drive external components for high-power-output applications. The TL497A was designed for ease of use in step-up, step-down, or voltage-inversion applications requiring high efficiency. The TL497A is a fixed-on-time variable-frequency switching-voltage-regulator control circuit. The switch-on time is programmed by a single external capacitor connected between FREQ CONTROL and GND. This capacitor, CT, is charged by an internal constant-current generator to a predetermined threshold. The charging current and the threshold vary proportionally with VCC. Thus, the switch-on time remains constant over the specified range of input voltage (4.5 V to 12 V). Typical on times for various values of CT are as follows: TIMING CAPACITOR, CT (pF) 200 250 350 400 500 750 1000 1500 2000 ON TIME ( µs) 19 22 26 32 44 56 80 120 180 The output voltage is controlled by an external resistor ladder network (R1 and R2 in Figures 1, 2, and 3) that provides a feedback voltage to the comparator input. This feedback voltage is compared to the reference voltage of 1.2 V (relative to SUBSTRATE) by the high-gain comparator. When the output voltage decays below the value required to maintain 1.2 V at the comparator input, the comparator enables the oscillator circuit, which charges and discharges CT as described above. The internal pass transistor is driven on during the charging of CT. The internal transistor can be used directly for switching currents up to 500 mA. Its collector and emitter are uncommitted, and it is current driven to allow operation from the positive supply voltage or ground. An internal Schottky diode matched to the current characteristics of the internal transistor also is available for blocking or commutating purposes. The TL497A also has on-chip current-limit circuitry that senses the peak currents in the switching regulator and protects the inductor against saturation and the pass transistor against overstress. The current limit is adjustable and is programmed by a single sense resistor, RCL, connected between VCC and CUR LIM SENS. The current-limit circuitry is activated when 0.7 V is developed across RCL. External gating is provided by the INHIBIT input. When the INHIBIT input is high, the output is turned off. Simplicity of design is a primary feature of the TL497A. With only six external components (three resistors, two capacitors, and one inductor), the TL497A operates in numerous voltage-conversion applications (step-up, step-down, invert) with as much as 85% of the source power delivered to the load. The TL497A replaces the TL497 in all applications. The TL497AC is characterized for operation from 0 °C to 70°C. The TL497AI is characterized for operation from −40 °C to 85°C. Copyright 2005, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. 1 2 3 4 5 6 7 14 13 12 11 10 9 8 COMP INPUT INHIBIT FREQ CONTROL SUBSTRATE GND CATHODE ANODE VCC CUR LIM SENS BASE DRIVE† BASE† COL OUT NC EMIT OUT (TOP VIEW) D, N, OR PW PACKAGE NC − No internal connection † BASE (11) and BASE DRIVE (12) are used for device testing only. They normally are not used in circuit applications of the device. |
Аналогичный номер детали - TL497AIJ |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |