поискавой системы для электроныых деталей |
|
LM124AWRLQMLV датащи(PDF) 7 Page - Texas Instruments |
|
|
LM124AWRLQMLV датащи(HTML) 7 Page - Texas Instruments |
7 / 31 page LM124AQML, LM124QML www.ti.com SNOSAE0K – AUGUST 2004 – REVISED MARCH 2013 LM124A/883 Electrical Characteristics SMD: 77043 DC Parameters (The following conditions apply to all the following parameters, unless otherwise specified.) All voltages referenced to device ground. Sub- Symbol Parameter Conditions Notes Min Max Unit Groups V+ = 5V 1.2 mA 1, 2, 3 ICC Power Supply Current 3.0 mA 1 V+ = 30V 4.0 mA 2, 3 V+ = 15V, VOUT = 200mV, 12 uA 1 +VIN = 0mV, -VIN = +65mV ISINK Output Sink Current V+ = 15V, VOUT = 2V, 10 mA 1 +VIN = 0mV, -VIN = +65mV 5 mA 2, 3 V+ = 15V, VOUT = 2V, -20 mA 1 ISOURCE Output Source Current +VIN = 0mV, -VIN = -65mV -10 mA 2, 3 IOS Short Circuit Current V+ = 5V, VOUT = 0V -60 mA 1 -2 2 mV 1 V+ = 30V, VCM = 0V -4 4 mV 2, 3 V+ = 30V, VCM = 28.5V -2 2 mV 1 VIO Input Offset Voltage V+ = 30V, VCM = 28V -4 4 mV 2, 3 -2 2 mV 1 V+ = 5V, VCM = 0V -4 4 mV 2, 3 Common Mode 70 dB 1 CMRR V+ = 30V, VIN = 0V to 28.5V (1) Rejection Ratio -50 10 nA 1 ±IIB Input Bias Current V+ = 5V, VCM = 0V (2) -100 10 nA 2, 3 -10 10 nA 1 IIO Input Offset Current V+ = 5V, VCM = 0V -30 30 nA 2, 3 Power Supply PSRR V+ = 5V to 30V, VCM = 0V 65 dB 1 Rejection Ratio Common Mode Voltage 28.5 V 1 (3) VCM V+ = 30V Range (1) 28 V 2, 3 V+ = 15V, RL = 2K Ω, 50 V/mV 4 AVS Large Signal Gain (4) VO = 1V to 11V 25 V/mV 5, 6 V+ = 30V, RL = 2K Ω 26 V 4, 5, 6 VOH Output Voltage High V+ = 30V, RL = 10K Ω 27 V 4, 5, 6 V+ = 30V, RL = 10K Ω 40 mV 4, 5, 6 40 mV 4 VOL Output Voltage Low V+ = 30V, ISINK = 1uA 100 mV 5, 6 V+ = 5V, RL = 10K Ω 20 mV 4, 5, 6 Channel Separation (5) 80 dB 4 1KHz, 20KHz Amp to Amp Coupling (6) (1) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The upper end of the common-mode voltage range is V+ −1.5V (at 25°C), but either or both inputs can go to +32V without damage independent of the magnitude of V+. (2) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so no loading change exists on the input lines. (3) Specified by VIO tests. (4) Datalog reading in K=V/mV (5) Ensured, not tested (6) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This typically can be detected as this type of capacitance increases at higher frequencies. Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 7 Product Folder Links: LM124AQML LM124QML |
Аналогичный номер детали - LM124AWRLQMLV |
|
Аналогичное описание - LM124AWRLQMLV |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |