поискавой системы для электроныых деталей |
|
ADP2443 датащи(PDF) 8 Page - Analog Devices |
|
ADP2443 датащи(HTML) 8 Page - Analog Devices |
8 / 25 page Data Sheet ADP2443 Rev. 0 | Page 7 of 24 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 2 1 3 4 5 6 18 17 16 15 14 13 SW SW GND VREG FB COMP PGND SW BST PVIN PVIN PVIN 25 GND ADP2443 TOP VIEW (Not to Scale) 26 SW NOTES 1. EXPOSED GND PAD. THE EXPOSED GND PAD MUST BE SOLDERED TO A LARGE, EXTERNAL, COPPER GND PLANE TO REDUCE THERMAL RESISTANCE. 2. EXPOSED SW PAD. THE EXPOSED SW PAD MUST BE CONNECTED TO THE SW PINS OF THE ADP2443 BY USING SHORT, WIDE TRACES, OR SOLDERED TO A LARGE EXTERNAL SW COPPER PLANE TO REDUCE THERMAL RESISTANCE. Figure 4. Pin Configuration Table 4. Pin Function Descriptions Pin No. Mnemonic Description 1 COMP Error Amplifier Output. Connect an RC network from COMP to GND. 2 FB Feedback Voltage Sense Input. Connect this pin to a resistor divider from the output voltage (VOUT). 3 VREG Output of the Internal 5 V Regulator. The control circuits are powered from the voltage on this pin. Place a 1 µF, X7R or X5R ceramic capacitor between this pin and GND. 4 GND Analog Ground. Return of internal control circuit. 5, 6, 7, 14 SW Switch Node Output. Connect these pins to the output inductor. 8 to 13 PGND Power Ground. Return of low-side power MOSFET. 15 BST Supply Rail for the High-Side Gate Drive. Place a 0.1 µF, X7R or X5R capacitor between SW and BST. 16 to 19 PVIN Power Input. Connect these pins to the input power source and connect a bypass capacitor between these pins and PGND. 20 EN Precision Enable Pin. An external resistor divider can be used to set the turn-on threshold. To enable the device automatically, connect the EN pin to the PVIN pin. 21 PGOOD Power-Good Output (Open-Drain). A pull-up resistor of 10 kΩ to 100 kΩ is recommended. 22 RT/SYNC Frequency Setting (RT). Connect a resistor between RT and GND to program the switching frequency between 200 kHz to 1.8 MHz. Synchronization Input (SYNC). Connect this pin to an external clock to synchronize the switching frequency between 200 kHz and 1.8 MHz. See the Oscillator section and the Synchronization section for more information. 23 RAMP Slope Compensation Setting. Connect a resistor from RAMP to PVIN to set the slope compensation. 24 SS Soft Start Control. Connect a capacitor from SS to GND to program the soft start time. 25 EP, GND Exposed GND Pad. The exposed GND pad must be soldered to a large, external, copper GND plane to reduce thermal resistance. 26 EP, SW Exposed SW Pad. The exposed SW pad must be connected to the SW pins of the ADP2443 by using short, wide traces, or soldered to a large external SW copper plane to reduce thermal resistance. |
Аналогичный номер детали - ADP2443 |
|
Аналогичное описание - ADP2443 |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |