поискавой системы для электроныых деталей |
|
9-305927-1 датащи(PDF) 6 Page - Tyco Electronics |
|
9-305927-1 датащи(HTML) 6 Page - Tyco Electronics |
6 / 7 page 411- 1097 Double Action Hand Crimping Tools 525690 and 525691 Rev D 6 of 7 Tyco Electronics Corporation Figure 8 Jaws Bottomed But Not Under Pressure Inspection of Wire Barrel Section of Crimping Chamber Inspection of Insulation Barrel Section of Crimping Chamber GO Element Must Pass Completely Through Crimping Chamber Insulation Crimp Adjustment Pins in Position 1 NO--GO Element May Start Entry, But Must Not Pass Completely Through Crimping Chamber GO Element Must Pass Completely Through Length of Insulation Barrel Section But Stop on Wire Barrel Section 4. Carefully insert the GO element into the crimping chamber as shown in Figure 8; DO NOT force it. For the wire barrel section of the crimping chamber, the GO element must pass completely through the crimping chamber. For the insulation barrel section, the GO element must pass through the length of the section but will stop against the wire barrel section. 5. In the same manner, try to insert the NO--GO element into the crimping chamber as shown in Figure 8. The NO--GO element may begin entry, but may not pass through the crimping chamber. If the crimping chamber conforms to the gage inspection, the tool is considered dimensionally correct, and should be lubricated with a THIN coat of any good SAE 20 motor oil. If not, return the tool for evaluation and repair. See Section 6, REPLACEMENT AND REPAIR. 5.3. Ratchet Inspection Check the ratchet to ensure that the ratchet does not release prematurely, allowing the jaws to open before they have fully bottomed. Proceed as follows: 1. Remove traces of oil or dirt from the bottoming surfaces of the jaws. 2. Obtain a 0.025 mm [.001 in.] shim that is suitable for checking the clearance between the bottoming surfaces of the jaws. 3. Select a terminal or splice and maximum size wire for the terminal or splice. 4. Position the terminal or splice in the crimping chamber according to Section 3, CRIMPING PROCEDURE. Holding the wire in place, squeeze the tool handles together until the ratchet releases. Hold the tool handles in this position, maintaining just enough pressure to keep the jaws closed. 5. Check the clearance between the bottoming surfaces of the jaws. If the clearance is 0.025 mm [.001 in.] or less, the ratchet is satisfactory. If clearance exceeds 0.025 mm [.001 in.], the ratchet is out of adjustment and must be repaired. See Section 6, REPLACEMENT AND REPAIR. 6. REPLACEMENT AND REPAIR Customer--replaceable parts are listed in Figure 9. A complete inventory should be stocked and controlled to prevent lost time when replacement of parts is necessary. Parts other than those listed should be replaced by Tyco Electronics to ensure quality and reliability. Order replacement parts through your representative, or call 1--800--526--5142, or send a facsimile of your purchase order to 717--986--7605, or write to: CUSTOMER SERVICE (038--035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105--3608 For customer repair service, call 1--800--526--5136. 7. REVISION SUMMARY Revisions to this instruction sheet include: S Updated document to corporate requirements S Added new data to tables in Figure 7 |
Аналогичный номер детали - 9-305927-1 |
|
Аналогичное описание - 9-305927-1 |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |