поискавой системы для электроныых деталей |
|
AM29F032B-150EE датащи(PDF) 10 Page - Advanced Micro Devices |
|
AM29F032B-150EE датащи(HTML) 10 Page - Advanced Micro Devices |
10 / 39 page Am29F032B 9 Characteristics” section contains timing specification tables and timing diagrams for write operations. Program and Erase Operation Status During an erase or program operation, the system may check the status of the operation by reading the status bits on DQ7–DQ0. Standard read cycle timings and I CC read specifications apply. Refer to “The Erase Resume command is valid only during the Erase Suspend mode.” for more information, and to each AC Charac- teristics section for timing diagrams. Standby Mode When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption is greatly reduced, and the outputs are placed in the high impedance state, inde- pendent of the OE# input. The device enters the CMOS standby mode when CE# and RESET# pins are both held at V CC ± 0.5 V. (Note that this is a more restricted voltage range than V IH.) The device enters the TTL standby mode when CE# and RESET# pins are both held at V IH. The device re- quires standard access time (t CE) for read access when the device is in either of these standby modes, before it is ready to read data. The device also enters the standby mode when the RE- SET# pin is driven low. Refer to the next section, “RE- SET#: Hardware Reset Pin”. If the device is deselected during erasure or program- ming, the device draws active current until the operation is completed. In the DC Characteristics tables, I CC3 represents the standby current specification. RESET#: Hardware Reset Pin The RESET# pin provides a hardware method of reset- ting the device to reading array data. When the system drives the RESET# pin low for at least a period of t RP, the device immediately terminates any operation in progress, tristates all data output pins, and ignores all read/write attempts for the duration of the RESET# pulse. The device also resets the internal state ma- chine to reading array data. The operation that was in- terrupted should be reinitiated once the device is ready to accept another command sequence, to ensure data integrity. Current is reduced for the duration of the RESET# pulse. When RESET# is held at V IL, the device enters the TTL standby mode; if RESET# is held at V SS ± 0.5 V, the device enters the CMOS standby mode. The RESET# pin may be tied to the system reset cir- cuitry. A system reset would thus also reset the Flash memory, enabling the system to read the boot-up firm- ware from the Flash memory. If RESET# is asserted during a program or erase oper- ation, the RY/BY# pin remains a “0” (busy) until the in- ternal reset operation is complete, which requires a time of t READY (during Embedded Algorithms). The sys- tem can thus monitor RY/BY# to determine whether the reset operation is complete. If RESET# is asserted when a program or erase operation is not executing (RY/BY# pin is “1”), the reset operation is completed within a time of t READY (not during Embedded Algo- rithms). The system can read data t RH after the RE- SET# pin returns to V IH. Refer to the AC Characteristics tables for RESET# pa- rameters and timing diagram. Output Disable Mode When the OE# input is at V IH, output from the device is disabled. The output pins are placed in the high imped- ance state. |
Аналогичный номер детали - AM29F032B-150EE |
|
Аналогичное описание - AM29F032B-150EE |
|
|
ссылки URL |
Конфиденциальность |
ALLDATASHEETRU.COM |
Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |